Good day, all!
I have seriouse problem with installing EX-1FE-FX (P\n: 740-021487) SFP-module, and I not shure that my SFP-module is compatibe with my swith. Please, help me to recognise module(see on picture).
And another question: if this module in compatible with my switch what I shall do to launch this module?
Some output of diagnostic commands:
1.
root@SW-01> show interfaces ge-0/1/0 detail
Physical interface: ge-0/1/0, Enabled, Physical link is Down
Interface index: 161, SNMP ifIndex: 555, Generation: 175
Link-level type: Ethernet, MTU: 1514, Speed: 100mbps, Duplex: Full-Duplex, BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled, Flow control: Disabled, Media type: Fiber
Device flags : Present Running
Interface flags: Hardware-Down SNMP-Traps Internal: 0x4000
Link flags : None
CoS queues : 8 supported, 8 maximum usable queues
Hold-times : Up 0 ms, Down 0 ms
Current address: b0:a8:6e:09:76:9b, Hardware address: b0:a8:6e:09:76:9b
Last flapped : Never
Statistics last cleared: Never
Traffic statistics:
Input bytes : 0 0 bps
Output bytes : 0 0 bps
Input packets: 0 0 pps
Output packets: 0 0 pps
IPv6 transit statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Egress queues: 8 supported, 4 in use
Queue counters: Queued packets Transmitted packets Dropped packets
0 best-effort 0 58303780 94881
1 assured-forw 0 0 0
5 expedited-fo 0 0 0
7 network-cont 0 18 0
Queue number: Mapped forwarding classes
0 best-effort
1 assured-forwarding
5 expedited-forwarding
7 network-control
Active alarms : LINK
Active defects : LINK
Interface transmit statistics: Disabled
Logical interface ge-0/1/0.0 (Index 93) (SNMP ifIndex 556) (Generation 177)
Flags: Device-Down SNMP-Traps 0x4000 Encapsulation: ENET2
Traffic statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Local statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Transit statistics:
Input bytes : 0 0 bps
Output bytes : 0 0 bps
Input packets: 0 0 pps
Output packets: 0 0 pps
Protocol eth-switch, Generation: 196, Route table: 0
Flags: None
{master:0}
2.
root@SW-01> show interfaces diagnostics optics ge-0/1/0
Physical interface: ge-0/1/0
Laser bias current : 12.650 mA
Laser output power : 0.0730 mW / -11.37 dBm
Module temperature : 34 degrees C / 93 degrees F
Module voltage : 3.1820 V
Receiver signal average optical power : 0.0308 mW / -15.11 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 90.000 mA
Laser bias current low alarm threshold : 0.000 mA
Laser bias current high warning threshold : 85.000 mA
Laser bias current low warning threshold : 0.000 mA
Laser output power high alarm threshold : 0.2230 mW / -6.52 dBm
Laser output power low alarm threshold : 0.0220 mW / -16.58 dBm
Laser output power high warning threshold : 0.1580 mW / -8.01 dBm
Laser output power low warning threshold : 0.0310 mW / -15.09 dBm
Module temperature high alarm threshold : 75 degrees C / 167 degrees F
Module temperature low alarm threshold : -5 degrees C / 23 degrees F
Module temperature high warning threshold : 70 degrees C / 158 degrees F
Module temperature low warning threshold : 0 degrees C / 32 degrees F
Module voltage high alarm threshold : 3.795 V
Module voltage low alarm threshold : 2.805 V
Module voltage high warning threshold : 3.465 V
Module voltage low warning threshold : 3.135 V
Laser rx power high alarm threshold : 0.5012 mW / -3.00 dBm
Laser rx power low alarm threshold : 0.0003 mW / -35.23 dBm
Laser rx power high warning threshold : 0.3162 mW / -5.00 dBm
Laser rx power low warning threshold : 0.0004 mW / -33.98 dBm
{master:0}
3.
root@SW-01> show chassis pic fpc-slot 0 pic-slot 1
FPC slot 0, PIC slot 1 information:
Type 4x GE SFP Builtin
State Online
Uptime 8 hours, 27 minutes, 33 seconds
PIC port information:
Fiber Xcvr vendor Wave- Xcvr
Port Cable type type Xcvr vendor part number length Firmware
0 GIGE 100LX SM FINISAR CORP FTLF1217P2BTL-J1 1310 nm 0.0
1 GIGE 100LX SM FINISAR CORP FTLF1217P2BTL-J1 1310 nm 0.0
2 GIGE 100LX SM FINISAR CORP FTLF1217P2BTL-J1 1310 nm 0.0
4.
root@SW-01> show chassis hardware
Hardware inventory:
Item Version Part number Serial number Description
Chassis 663023100JZ EX2200-24T-4G
Routing Engine 0 REV 11 750-037483 663023100JZ EX2200-24T-4G
FPC 0 REV 11 750-037483 663023100JZ EX2200-24T-4G
CPU BUILTIN BUILTIN FPC CPU
PIC 0 BUILTIN BUILTIN 24x 10/100/1000 Base-T
PIC 1 REV 11 750-037483 663023100JZ 4x GE SFP
Xcvr 0 REV 01 740-021487 AN24B20 SFP-100-LX
Xcvr 1 REV 01 740-021487 AN24B27 SFP-100-LX
Xcvr 2 REV 01 740-021487 AN24B28 SFP-100-LX
Power Supply 0 PS 100W AC
Fan Tray Fan Tray
{master:0}
P.s. This module startup and work property wit MOXA IMC-21GA Ethernet converter.
P.p.s Sory for my English 