Here is the diagnostic output for the Juniper6 port ge-0/0/30:
Physical interface: ge-0/0/30
Laser bias current : 6.320 mA
Laser output power : 0.2850 mW / -5.45 dBm
Module temperature : 29 degrees C / 83 degrees F
Module voltage : 3.2980 V
Receiver signal average optical power : 0.3273 mW / -4.85 dBm
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 12.000 mA
Laser bias current low alarm threshold : 2.000 mA
Laser bias current high warning threshold : 10.000 mA
Laser bias current low warning threshold : 2.000 mA
Laser output power high alarm threshold : 1.1000 mW / 0.41 dBm
Laser output power low alarm threshold : 0.0600 mW / -12.22 dBm
Laser output power high warning threshold : 1.0000 mW / 0.00 dBm
Laser output power low warning threshold : 0.0850 mW / -10.71 dBm
Module temperature high alarm threshold : 100 degrees C / 212 degrees F
Module temperature low alarm threshold : -40 degrees C / -40 degrees F
Module temperature high warning threshold : 85 degrees C / 185 degrees F
Module temperature low warning threshold : -10 degrees C / 14 degrees F
Module voltage high alarm threshold : 3.630 V
Module voltage low alarm threshold : 2.970 V
Module voltage high warning threshold : 3.465 V
Module voltage low warning threshold : 3.134 V
Laser rx power high alarm threshold : 1.8000 mW / 2.55 dBm
Laser rx power low alarm threshold : 0.0000 mW / - Inf dBm
Laser rx power high warning threshold : 1.0000 mW / 0.00 dBm
Laser rx power low warning threshold : 0.0200 mW / -16.99 dBm
And here is what I can find for the other end (ASR1 Gig0/0/5):
The Transceiver in slot 0 subslot 0 port 5 is enabled. Module temperature = +23.464 C Transceiver Tx supply voltage = 3281.0 mVolts Transceiver Tx bias current = 5906 uAmps Transceiver Tx power = -4.9 dBm Transceiver Rx optical power = -5.5 dBm
IDPROM for transceiver GigabitEthernet0/0/5:
Description = SFP or SFP+ optics (type 3)
Transceiver Type: = GE SX (19)
Product Identifier (PID) = GLC-SX-MMD
Vendor Revision = A
Serial Number (SN) = FNS18272505
Vendor Name = CISCO
Vendor OUI (IEEE company ID) = 00.90.65 (36965)
CLEI code = WOTRB9VBAA
Cisco part number = 10-2626-01
Device State = Enabled.
Date code (yy/mm/dd) = 14/07/03
Connector type = LC.
Encoding = 8B10B
NRZ
Nominal bitrate = GE (1300 Mbits/s)
Minimum bit rate as % of nominal bit rate = not specified
Maximum bit rate as % of nominal bit rate = not specified
The transceiver type is 19
Link reach for 9u fiber (km) = SX(550/270m) (0)
1xFC-MM(500/300m) (0)
2xFC-MM(300/150m) (0)
ESCON-MM(2km) (0)
Link reach for 9u fiber (m) = SX(550/270m) (0)
1xFC-MM(500/300m) (0)
2xFC-MM(300/150m) (0)
ESCON-MM(2km) (0)
Link reach for 50u fiber (m) = SX(550/270m) (55)
LX(5km/550m) (55)
LX(10km/550m) (55)
Nominal laser wavelength = 850 nm.
DWDM wavelength fraction = 850.0 nm.
Supported options = Tx disable
Loss of signal (standard implementation)
Diagnostic monitoring = Digital diagnostics supported
Diagnostics are internally calibrated
Rx power measured is "Average power"
Transceiver temperature operating range = -5 C to 85 C (extended)
Minimum operating temperature = -5 C
Maximum operating temperature = 85 C
High temperature alarm threshold = +90.000 C
High temperature warning threshold = +85.000 C
Low temperature warning threshold = -5.000 C
Low temperature alarm threshold = -10.000 C
High voltage alarm threshold = 3600.0 mVolts
High voltage warning threshold = 3500.0 mVolts
Low voltage warning threshold = 3100.0 mVolts
Low voltage alarm threshold = 3000.0 mVolts
High laser bias current alarm threshold = 15.000 mAmps
High laser bias current warning threshold = 12.000 mAmps
Low laser bias current warning threshold = 2.000 mAmps
Low laser bias current alarm threshold = 1.000 mAmps
High transmit power alarm threshold = 0.0 dBm
High transmit power warning threshold = -3.0 dBm
Low transmit power warning threshold = -9.5 dBm
Low transmit power alarm threshold = -13.5 dBm
High receive power alarm threshold = 3.0 dBm
High receive power warning threshold = 0.0 dBm
Low receive power warning threshold = -17.0 dBm
Low receive power alarm threshold = -21.0 dBm
External Calibration: bias current slope = 1.000
External Calibration: bias current offset = 0