Re: Routing issues
My issue is resolved. Worked with another colleague who discovered the interface was inheriting a config from another interface. Interface is now in the correct VLAN and routing table entries are...
View ArticleRe: EX2200-C virtual chassis Junos 15.1R6.7
Due to memory contraint issue 15.1 Junos is not recommended for EX2200 switch.https://kb.juniper.net/InfoCenter/index?page=content&id=TSB17138&cat=&actp=LIST Regards,Kiran
View ArticleRe: EX4500 mac table grows to limit, all mac ages are 0
Thanks for your reply! I don't have unlimited aging I think: > show configuration protocols l2-learning ^ syntax error.> show configuration ethernet-switching-options mac-table-aging-time 180;I...
View ArticleRe: EX4500 mac table grows to limit, all mac ages are 0
Another thing to add: If I clear the mac table it ends up being about 5000 entries, and it continuouosly grows up to the 32k limit unless I clear it again.
View ArticleProcurve to Juniper ping issue
Hi Everyone. Equipment: Procurve 5406, Ex4300, and ex2200 ->Device (10.4.10.1). I'm having problems with the 5406 (Core) pinging a device on the 2200. 2200 can ping the device. 4300 & Core...
View ArticleRe: ex4300 vs ex4200 reachability through bridge
Config in set format is in initial post. root# run show route 10.10.10.21inet.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)+ = Active Route, - = Last Active, * = Both10.10.10.0/24...
View ArticleRe: ex4300 vs ex4200 reachability through bridge
Yes it's up up. I'm leaning towards irb interfaces not supporting this type of connection. I deleted the irb.112 interface and assigned my IP to a physical interface(family inet) and just used an L2...
View ArticleRT Error Messages EX4300
Not sure what these errors mean - could you help decipher them? Switch version: Model: ex4300-32fJunos: 14.1X53-D35.3JUNOS EX Software Suite [14.1X53-D35.3]JUNOS FIPS mode utilities...
View ArticleRe: RT Error Messages EX4300
Google suggests that indicates a low memory or resource (e.g. arp table) condition. I'm sure jtac could confirm.
View ArticleRe: RT Error Messages EX4300
I have 321 total ARP entries on the switch. I would imagine it would be much higher than that. Memory utilization is sitting around 33%, and .33 load average.
View ArticleEX3400 COS transmit rate
Hi all, I am receiving the following messages on my EX3400 running 15.1X53-D55.5: Aug 8 15:18:01 EX3400-DC1 dc-pfe: BRCM_COS_HALP(brcm_cos_ng_access_bind_scheduler_map_ifd:2583): Transmit rate...
View ArticleRe: EX3400 COS transmit rate
Looks like there is some problem translating % transmit rate to bps on this interface. I assume 2583 is interface index.Please run show interfaces | match "physical|2583" When you know wchich interface...
View ArticleRe: ex4300 vs ex4200 reachability through bridge
Sounds like a bug in the version of Junos you have. You can ping irb interface ip addresses in configurations I've had in the past.
View ArticleRe: Procurve to Juniper ping issue
The link on the ex2200 is an AE interface with a minimum links of 2.What is the second physical link?Is ae0 up/up?show interface terse ae0ae0 { description "Default Network"; aggregated-ether-options {...
View ArticleRSTP on EX3400 et interface
Hi together, I have a little problem with two EX3400. These switches should use rstp. Both switches have two uplinks to two different switches via the et interfaces on the back of the switches. The...
View ArticleRe: Strange log messages in EX2300
Yes, we have SNMP requests to this switch. I will double check templates and look if it's realy SNMP causes messages to appear.Thank you.
View ArticleRe: Procurve to Juniper ping issue
Yes that solved this problem. I kinda forgot I unplugged it... But I unplugged it do some troubleshooting for devices with sporadic ping issues. But that's a discussion for another thread. Thanks for...
View ArticleSporadic Ping Issue
Hi Everyone,So I had this problem yesterday.But that was all because I was trying to troubleshoot this problem.I have 4 devices on 2200's that will ping for a bit then just stop. Randomly it would be...
View ArticleRe: EX-4600
thankx alot these configuration worked out and helped me alot ... i still have an issue with the bootp . How to configure the bootp with DHCP relay .. set forwarding-options dhcp-relay server-group...
View Article