cant route between vlans (SRX & EX)
i configured ae0 aggragation link between SRX and EX switches as below:the link worked but i want SRX to route between these vlans. when i tried to add interface ae0 to zone trust i got an error to...
View ArticleEX2300-C which license for VC
Hello, I want to create a virtual chassis using 2x EX2300-C-12P switches.In the future this virtual chassis will be extended with one or two EX2300-24P. From what I understand it's possible to do...
View ArticleRe: EX2300-C which license for VC
Not sure why the confusion. Since EX2300 VC (whether -C there or not) requires a license per switch, you would purchase the EX-12-EFL for EX2300-C and EX-24-EFL for EX2300, no? Separate different...
View ArticleRe: Interface storming for validation of physical interface robustness
Stepping back, I'm wondering why the input packet reject count doesn't specifiy why the reject is occuring; no sa or da reject count. Is there another way to trace what mechanism is causing the actual...
View ArticleRe: cant route between vlans (SRX & EX)
On the SRX you add interfaces to the zone down to the unit number.So these are the interfaces you would add to the zoneae0.1ae0.2
View ArticleRe: QFX3500-48s4q-acrb stuck in virtual chassis/linecard config
I agree that this is starting to look like a hardware RMA will be needed.I suggest you open a JTAC ticket for review.
View ArticleEX-2200 Can't ping RVI interface itself from hosts belonging to other vlan
Maybe I'm new in Juniper Network and you'll find a fast resolution for this issue.But, following my past experience in networking and security, this problem still strange for me :-) SIMPLIFY LAB...
View ArticleRe: EX-2200 Can't ping RVI interface itself from hosts belonging to other vlan
PROBLEM SOLVED Configuration was correct. It was some IP overlapping in my system that will cover the same ip addressing used on my lab. :-P
View ArticleJ-Web, Flash to HTML5, when?
The title says it all. Currently J-Web on our switches (EX4200, EX4500, and EX4600) uses Flash to render certain parts of the interface. When is Juniper going to release a version of J-Web that uses...
View ArticleRe: Juniper switch support for the newly approved 802.3bz standard
I haven't seen any product announcments, but are we still looking at Q1 2018 do you think?
View ArticleClik here to view.
QFX igmp-snooping not working
Hi, I have some issue over igmp-snooping with a QFX5100. Setup is simple (keep in mind, I did try to make it work only with the switch) I receive multicast stream over interface xe-0/0/1.0 wich is...
View ArticleRe: QFX igmp-snooping
Can you share your snooping configuration?https://www.juniper.net/documentation/en_US/junos/topics/concept/igmp-snooping-qfx-series-overview.html
View ArticleRe: QFX igmp-snooping
yes, it's very simple:Yes, here we are. I dont think the first interface is needed: vlan CARRIER { interface xe-0/0/1.0 { multicast-router-interface; } interface irb.12 {...
View ArticleRe: QFX igmp-snooping not working
Hi !you wrote:The second I enable snooping, all traffic goes down" Did you wait 3 minutes and look what happens then, or did you close and reopen the receiver application, as... all Multicast protocols...
View ArticleRe: QFX igmp-snooping not working
I did removed my snooping and my servers was able to see the stream again. Let me try to wait and restart the application.
View ArticleRe: QFX igmp-snooping not working
Ok, I did try to wait and restart my application.. stil noting works. From what I see, the traffic on the CARRIER port, from wich multicast is comming didn't stopped compared to all other ports when I...
View ArticleRe: QFX igmp-snooping not working
there are some strange things in your output1. IGMP version ( the default is 2 ) but in the statistics I see V1 and V3 reports !!!!which version did you configure ?2. the interface in the snooping...
View ArticleRe: EX2300-C which license for VC
Hello, The confusion for me is that different sources give different information. It's possible to buy a license that only permits VC; or a license that permits VC + various enhanced features.I was...
View ArticleClik here to view.
EX3300 LAG (LACP) strange behavior
Hello guys.I have a 2 x XE port LACP going from an EX300 virtual chassis (lets call it EX-VC) to en EX3300 standalone (lets call it EX).I have configured the EX-VC as such:# show interfaces xe-0/1/1...
View ArticleRe: EX3300 LAG (LACP) strange behavior
HI Iodcdk Can you please paste me the output of show chassis hardware detail on EX-VC ?Is the transeiver plugged-in properly ?What code you are running ?The partner in EX-VC should be xe-0/1/0
View Article