Re: EX4550 triangle connectivity - RSTP issues
Hello,Of coursehttps://www.juniper.net/documentation/en_US/junos/topics/example/interfaces-layer3-subinterfaces-ex-series.htmlHTHThxAlex
View ArticleRe: Can Juniper generate traffic out of an interface?
Hello,The short answer is yeshttps://www.juniper.net/documentation/en_US/junos/topics/task/configuration/rfc2544-benchmarking-test-configuring.htmlThe long answer is that hardware traffic generators...
View ArticleEX3300 Bandwith Limitations
Hi All, I am not really new to juniper but not an expert also.. Anyway i am running into something for a customer of ours..A customer of ours needs to have a bandwith limit on all of their ports.I've...
View ArticleRe: Can Juniper generate traffic out of an interface?
Thanks for the responses. The initial idea in https://forums.juniper.net/t5/Ethernet-Switching/Interface-storming-for-validation-of-physical-interface/m-p/317706#M17566 was to not use Juniper as a...
View ArticleRe: EX3300 Bandwith Limitations
Hi, Policer is not supported for egress. You can use ingress policing and egress shaping. root@test# commit [edit] 'filter' Referenced filter 'RATE-LIMIT' can not be used as policer not supported on...
View ArticleWhere did these packets go?
I'm trying to figure out why these packets were dropped, 'rejects' should be rejected because of SA or DA, but neither SA or DA reject counts are incrementing. This is in a MX480 with...
View ArticleRe: Where did these packets go?
What packets? Do you know which exact packet [type] are being dropped? BTW, you config is for interfaces 5/0/2 and 5/0/5 both in VLAN-100. I assume traffic flows between this 2 interfaces; BUT your...
View ArticleRe: Where did these packets go?
Also, is there a specific reason you have enabled no-mac-learning for the VLAN/bridge-domain? For this config option there should never be drops due to SA or DA, as they should be ignored. The drops...
View ArticleEX2200 can't join in boot -s (single mode) auto rebooting
Hello there, im looking for some ideas about what is happen with my two junipers switches, I don't remember the password so Im trying to follow the root password recovery procedure but after put boot...
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
Hi Slack, Could you please ensure that there no USB attached to switch while you do enter "boot -s"? https://kb.juniper.net/InfoCenter/index?page=content&id=KB14102...
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
Thanks, but that don't work. I did without any usb connected and the same happen when I put "boot -s" after some loading, the "Rebooting..." message appears and the device is rebooted.
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
Try this medthod, the one at the end, type only "-s" at the boot: prompt and see how it goes?https://forums.juniper.net/t5/Ethernet-Switching/Unable-to-reset-password-on-EX2200/td-p/104234
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
Why not just RMA the switch? Unit Is covered under ELLW, which provides next-day ship, even with no service contract.
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
I wouldn't suggest RMA & why RMA? An RMA should be only when you have H/w issue with device.This is not H/w issue. Also, for RMA, you will need to log a ticket with JTAC, insteand of RMA, raise a...
View ArticleRe: EX2200 can't join in boot -s (single mode) auto rebooting
Hi karand, I don't see any like that to just put "-s".
View ArticleRe: EX4550 triangle connectivity - RSTP issues
I've raised a case with our Support partner and am still getting no comfortable feeling from them as to why RSTP is still blocking my interfaces.All links between switches have now been configured as...
View ArticleQFX5100 and DHCP snooping
Hi! I have:QFX5100-48S-6QJunos: 17.4R1.16 I want to configure DHCP snooping for protect my network from other DHCP servers...I use this guide:...
View ArticleClik here to view.
Re: EX4550 triangle connectivity - RSTP issues
I have resolved this by enabling VSTP on the interfaces forming the triangle. As each link has a unique VLAN, there are now no ports being blocked I have left RSTP enabled also, but disabled it on all...
View ArticleRe: QFX5100 and DHCP snooping
Per this it should be there - https://apps.juniper.net/feature-explorer/feature-info.html?fKey=1039&fn=DHCP%20snooping See here for details on how to configure -...
View ArticleRe: QFX5100 and DHCP snooping
Hello, But a dont have ethernet-switching-options: am> configure Entering configuration mode {master:0}[edit] am# set et ^ syntax error. am# set et
View Article