Quantcast
Channel: All Ethernet Switching posts
Browsing all 10307 articles
Browse latest View live

Re: QFX-10002 filter on GRE issue

Filter does not get programmed when applied on gr-0/0/0 but get programmed for normal interface. TFXPC0(vty)# show filter hw 6Filter:test (Index:6) Type IPv4 phdl:0x6fa73199 flags:0 n_anh:0...

View Article


Re: QFX-10002 filter on GRE issue

Hi! You may be right. But we need to be absolutely sure in this verdict. I'll try to ask JTAC about this.To be honestly it's very sad to face that kind of limitation for this powerful hardware.

View Article


Re: QFX-10002 filter on GRE issue

I agree with Anton. If it isn't supported, then it should at least return a warning. When I read the note it's relevant for the tunnel sources interfaces (in my case an et-0/0/x interfaces) but should...

View Article

Re: What kind of Juniper device can I use as a CPE?

I would respectfully disagree on the SRX not being designed as a Service Provider CPE. AT&T and Verizon both use them as CPE for most of their business services and the fact that the SRX is...

View Article

Re: What kind of Juniper device can I use as a CPE?

Sure the SRX in packet mode can and is used as a CPE but it is far less capable than the ACX.  We run hundreds as opposed to thousands of these devices at the edge.  The SRX only supports a subset of...

View Article


Re: Juniper-Huawei MPLS TE-RSVP - hello packets issue

Hello, thank you for the reply. I have solved this issue  - indeed there were problems with it.Now I have RSVP sessions UP HW-JN. I can even set tunnel HW-JN and the tunnel-interface is UP. I have last...

View Article

Re: Juniper-Huawei MPLS TE-RSVP - hello packets issue

Hi,what errors/symptoms have you got now? Or it's just not working as expected?

View Article

Re: Juniper-Huawei MPLS TE-RSVP - hello packets issue

Hello, it is not setting up a LSP Huawei -> Huawei through Juniper.Juniper is setting UP LSP with all connected to it Huaweis (4), but its not transiting  session(?)/LSPs(?) between two Huaweis.I...

View Article


Re: Juniper-Huawei MPLS TE-RSVP - hello packets issue

Hi, Try to check the outpur from show route table mpls.0 command.It must contains a transit LSP has built on RSVP.

View Article


Re: Juniper-Huawei MPLS TE-RSVP - hello packets issue

Hello, I  dont have any of RSVP LSP in mpls.0 . I have in table inet.3 RSVP LSP but only those which Juniper is Ingress for. No transit LSP with SWAP table.What should I turn on? Which option am I...

View Article

Re: Enabling Proxy Arp

Just enabled proxy-arp unrestricted and broke direct communications on the subnet. So no hosts could see each other anymore.Gladfully had "commit confirmed 1"! No, it's not like Cisco. Cisco is just...

View Article

Re: ex2200/3300 VOIP phone does not DOT1x with pc plugged in

Working with juniper on this ongoing but i wanted to update  Juniper found a bug, if we remove the lo0 filter (protect RE) the device connected fine. this is our protect RE filter and is NOT set to...

View Article

Re: Integrating Juniper switches with Cisco Identity Services Engine NAC...

how about url web-redirection, as it is needed for ISE posture, does Juniper Switches support it? Haven't found any documentation about it.

View Article


Re: Enabling Proxy Arp

My understanding is switch/router won't do the proxy ARP if the destination is not reachable from the network from where the ARP is initiated. There could be some element in your network preventing...

View Article

Re: How add IRB interface to SVLAN used for q-in-q

Hi, Any help ?Regards,Lish

View Article


Re: Enabling Proxy Arp

I found out the reason why my proxy arp restricted did not work.My conclusion: proxy arp is done only on the VRRP master interface. Additionally in my config I have two VRRP groups (rebuild in office...

View Article

Re: Enabling Proxy Arp

Correction: proxy-arp is doing that side that got the last transition to master.Means: As soon as one of the groups becomes master the arp response is then sent from there.

View Article


EX4600, Junos 14.1 or 17.3?

We have a stack of two EX4600s that form the core of our network and provided layer 2/3 services. They are currently running Junos 14.1X53-D46.7. Twice a year we upgrade to whatever version of Junos...

View Article

Re: EX4600, Junos 14.1 or 17.3?

Just my personal experience:if you do NOT need any features new in higher versions and you are happy with the 14.1X53 then stay on that train, as the D47 is only a a version with slightly more bugs...

View Article

Re: EX4600, Junos 14.1 or 17.3?

The difficulty is trying to tease out exactly what are the differences between these two strands of code. I cannot find any concise documentation that shows a comparison between these two and talks...

View Article
Browsing all 10307 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>