Re: Best practices and configuration changes
The firewall filters are applied to the routed vlan interfaces themselves so only need to be applied on the switch with these interfaces configured. The downstream switches in your case have only one...
View ArticleBetreff: difference between EX4600
Does EX4600 come with a two power supplies ?in other words if i'm going to use it with another EX4600 in a VC shall I purchase another power supply to avoid failure in the power source ?or it is...
View ArticleClik here to view.
Betreff: difference between EX4600
Hi HDawood, 1] Yes, the EX4600 is shipped from the factory with two power supplies. Each power supply is a hot-removable and hot-insertable field-replaceable unit (FRU) when the second power supply...
View ArticleRe: Best practices and configuration changes
If I could trouble you, an example would be great.
View ArticleRe: Best practices and configuration changes
This is a generic example of controling traffic on ex switches with firewall filters. https://www.juniper.net/documentation/en_US/junos/topics/example/firewall-filter-ex-series-configuring.html
View ArticleRe: SKU last order date
@HDawood I am not sure where you are getting your info from, but that SKU (JNP-10G-SR-8PACK) is still in the Juniper Price List as of June, and I do not remember any End of Sale announcement for that...
View ArticlePower supply
In qfx5100 device, is there a zone to which power entry module belongs to. Can I remove one pem when another pem is in the chassis rack. I am concerned that this mustn't take my device offline. I know...
View ArticleRe: EX3300/3400 - Change Primary interface (instead of lo0)
Hello, thanks for you response.I added a new IP to the lo0 and marked it as primary, and configured the -default-address-selection.But even with that i still see the...
View ArticleRe: EX3300/3400 - Change Primary interface (instead of lo0)
Hi Spluka,Yes adding the options for 'source-adress' and 'routing-instance' does help my problem with certain configuration like radius and etc.But i cant seeem to get it working with NTP, and...
View ArticleClik here to view.
Re: Power supply
Hi Reload, To answer your queries: 1) As per my knowledge, there is no zone concept in QFX series devices as seen in MX. One reason why I believe this to be true is, the power supplies are 1+1...
View ArticleRe: Power supply
Hi, Power supplies should be redundent to each other not having certain power zones to serve. If this solves your problem, please mark this post as "Accepted Solution.
View ArticleRe: EX2300 running 18.1R3.3. not able to change speed for DAC connector on XE...
Hi everybody,I finally got that up and running. I've disabled the xe-0/1/1 port and enabled ge-0/1/1 port. Then I configured trunk mode including targeted VLAN subnets and the link became available...
View ArticleClik here to view.
Re: Power supply
Hi Reload, Greetings, The QFX5100 is shipped from the factory with two power supplies. Each power supply is a hot-removable and hot-insertable field-replaceable unit (FRU) when the second power supply...
View ArticleRe: Does EX Switch support G8032v2 ?
Hi Sharat, Thanks for your answer.Actually I want to know if there is an EX Series Switch that support G8032v2. Regards
View ArticleRe: Best practices and configuration changes
Thats exactly the same document I've referenced. The syntax vary between that and the version on my switch. For example I have to use following:edit firewall family ethernet-switching filter vlan_50...
View ArticleClik here to view.
Re: Does EX Switch support G8032v2 ?
Hi Septo_DW Greetings, I believe G8032v2 is not supported on the EX series switches. As per this documentation : Using G.8032 Ethernet Stitching released on Feb 2017(which is quite old for now) .By...
View Articledistance on optic interfaces
hi all,There are optic devices on the qfx. How to determine about how many km optic devices can support? And what is the difference between 1310 and 1533nm? >show chassis pic fpc-slot 0 pic-slot 0...
View ArticleRe: Does EX Switch support G8032v2 ?
Hi Sharat, Thanks for your help, really appreciate it.
View ArticleClik here to view.
Re: distance on optic interfaces
Hey Arix, Greetings,The values 1310nm and 1533nm are wavelength values for the optics. Typically, 1310nm is used for single-mode shorter length applications. Whereas 1533nm is used for extremely long...
View Article