Re: Router-on-a stick Cisco Router with Juniper Switch
Well, Thanks to everyone who helped me, shame we never figured out the actual root of the problem. Really hope this doesn't pop up again. Thanks.
View ArticleExtremely strange issue: forwarding plane packets hitting routing engine...
We asked an expert, he doesn't know what's going on. I'm not sure even junos devs know what's up here. We've got two EX4200, 12.3R12.4 in VCP. Say, 2 hosts are connected to the switch. Ports (access...
View ArticleRe: Extremely strange issue with forwarding plane packets hitting routing...
Have you a several ip subnets that configured on the SINGLE VLAN? Right?Do you have static or default routes configured on hosts to reach another subnet's hosts?
View ArticleClik here to view.
Re: QNAP TS-639 & 4300 EX Link aggregation does not work
Hi Ashvin, You are amazing !!!: Link-level type: Ethernet, MTU: 1514, Speed: 2Gbps, BPDU Error: None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled Get my 2GB speed of both...
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
user@EX-4200-Stack1> show route 10.255.0.3 inet.0: 185 destinations, 186 routes (185 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 10.255.0.3/32 *[OSPF/110] 04:29:29,...
View ArticleRe: mvrp and QFX
David,I've been performing some of my own testing using a test rig of EX4550 <--> EX2200 <-> QFX5100 all running MVRP.Couple of really interesting points here which have snagged me up in...
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
HiThe same policy should be able to load balance traffic for equal cost multi paths.Can you check:show mpls lspshow route forwarding-tableIf the LSPs have equal metrics, the traffic would be load...
View ArticleAD authentication failure - RADIUS Windows 2012R2 setup
We have a working Windows 2012R2 NPS server running our wireless network at the moment and I want to add the juniper devices to it. EX4200 and EX2200 mostly. I have the following config changes...
View Article4300 LACP for Aerohive Access Point in aggregate mode
Dear Experts, I am trying to set the config for Aerohive access point in ether channel LACP. here is my juniper config: AE13: description AP230LACP;native-vlan-id 198;aggregated-ether-options { lacp {...
View ArticleRe: AD authentication failure - RADIUS Windows 2012R2 setup
1. Select “Vendor Specific” under the RADIUS Attributes 2.Click Add, change the Vendor dropdown to “Custom” and click “Vendor-Specific” from the attributes 1.Click “Add”, then “Add” on the “Attribute...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
You'll need to remove interfaces which you are trying to aggregate from xstp protocol (rstp by default):delete protocols rstp interface ge-1/0/38 delete protocols rstp interface ge-0/0/24and then turn...
View ArticleRe: AD authentication failure - RADIUS Windows 2012R2 setup
Yes, went throught that several times deleting and re-creating with support. No luck Here is a run down of the server setup at the moment.RADIUS Clients and Servers: Radius Clients: New Radius Client...
View ArticleRe: AD authentication failure - RADIUS Windows 2012R2 setup
Just did some additional testing and it turns out that it is working on EX4200 and EX3200 models, but not on EX2200 series. Is that a known thing that I missed?
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Thank You so much - that fixed the problem, but now: show interfaces ae13Physical interface: ae13, Enabled, Physical link is Down Interface index: 653, SNMP ifIndex: 619 Description: WC508 Link-level...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Aggregated interface: ae13 LACP state: Role Exp Def Dist Col Syn Aggr Timeout Activity ge-1/0/38 Actor No Yes No No No Yes Fast Active ge-1/0/38 Partner No Yes No No No Yes Fast Passive ge-2/0/34 Actor...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
So actually which interfaces are belong ae13?run "show interface ae13 detail" command please.
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
sorry for the confusion, yes the ports are: Physical interface: ae13, Enabled, Physical link is Down Interface index: 653, SNMP ifIndex: 619, Generation: 147 Description: WC508 Link-level type:...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Hi, Statistics indicate no LACP PDUs are being received:LACP Statistics: LACP Rx LACP Tx Unknown Rx Illegal Rx ge-1/0/38.0 0 5296 0 0 ge-2/0/34.0 0 716 0 0Is the facing device configured with...
View ArticleRe: Extremely strange issue with forwarding plane packets hitting routing...
interfaces vlan unit 123 family inet {address 1.1.1.1/24;address 1.1.2.1/24;address 1.1.3.1/24;} hosts have default routes pointing to respective gateway address.
View ArticleRe: QNAP TS-639 & 4300 EX Link aggregation does not work
Hi,Yes, for ae21 [ae0 to ae21; Total 22] the chassis should be enabled for minimum 22 aggregated device-count.Else the ae22 interface will report as "device not found".set chassis aggregated-devices...
View Article