Re: EX4550 with l3 interface in a Private VLAN
Many thanks for the reply! I've tried to apply, but it does not seem to work: set vlans pvlan vlan-id 100 set interfaces ae1 unit 0 family ethernet-switching port-mode trunk set interfaces ae1 unit 0...
View Articleuplink Juniper EX2300-t to Zxyel XGS1910 using fibre ports
Hi All This may have been answer here already so apologies if it has, but i'm looking to see if it possible to connect my stack of 3 EX2300-T switches to my other Zxyel XGS1910 switch using a SPF+...
View ArticleRe: Procedure to add a new member to a Juniper stack.
Hello alchemy24, What is the hardware platform?Do you have same JunOS version on all boxes?Have you tried to swap cable and/or transceivers? Thanks,Deimos.
View ArticleBetreff: uplink Juniper EX2300-t to Zxyel XGS1910 using fibre ports
Hello JP, yes. both EX2300-T and Zyxel XGS1910 support 10G SFP+ modules. Here you can see which kind of 10G SFP+ modules the EX2300 device supports (you need to scroll down to "10 Gigabit Ethernet"):...
View ArticleRe: Error when login via console
Hello HDawood, Does the device work properly in general after the upgrade?Only console is not working and shows mentioned error message? Thanks,Deimos.
View ArticleRe: Procedure to add a new member to a Juniper stack.
Hi, I finally found the problem.When I listed the config on both switch (by running the "show | display set", I was getting the same version 18.1R3.3.But when running "show version" We could see that...
View ArticleRe: EX4550 with l3 interface in a Private VLAN
Hi amn. I hope everything is ok with you. I checked your config and also tested in my Lab , the same commit error came up. I am afraid that what you are trying to do is not supported, L3 interface in...
View ArticleRe: EX4550 with l3 interface in a Private VLAN
I have just tested the following config on a QFX5110 and has previously also used it for educational purposes on an EX3400 where it worked as expected. Please try to alter you config to match this and...
View ArticleRe: Error when login via console
no it didn't work , it opens the loader then nothing work.
View ArticleRe: unable to commit
Hello Merkaza, Please also check the "vlans" hierarchy, interface could be add as a member of vlan there as well.user@switch# set vlans vlan-name interface interface-name Thanks,Deimos.
View ArticleRe: EX4550 with l3 interface in a Private VLAN
Many thanks for your help again. I think the platform is limited in terms of options and the command private-vlan under vlans does not exist, below are the possible options for the vlan portion. It...
View ArticleRe: EX4550 with l3 interface in a Private VLAN
Many thanks for your help. I did follow this very documentation. I can configure private-vlan, but I cannot configure an irb or vlan l3 interface. I would assume this is, indeed, a platform limitation...
View ArticleRe: EX4550 with l3 interface in a Private VLAN
Hi amn. Based on the link provided I'd say that all the legacy platforms like (EX2200-Ex3300-EX4500)do not support that feature, however, as mentioned above by jonashauge it seems to work on ELS...
View ArticleBetreff: uplink Juniper EX2300-t to Zxyel XGS1910 using fibre ports
Thanks for that would you have link to setting up the VC members? What type of fibre cables do EX2300 support - LC or VC?
View ArticleRe: BPDU LoadBalancing with ae interface
Thanks for you reply Akushner. What do you mean by first interface in the LAG ? first interface that show in "show lacp interface aeX" ? smallest interface snmp index ? first interface in manming order...
View ArticleRe: BPDU LoadBalancing with ae interface
Hi Salah, I hope you are having a nice day! Regarding your questions: All RE generated packets that traverse the LAG, such as protocol control traffic, will use the lowest member link.So if you have a...
View ArticleRe: BPDU LoadBalancing with ae interface
that should be lowest one (xe-9/0/0). After interface (xe-9/0/0) flaps and came up all host outbound packets will be send from this interface again
View ArticleRe: CWA in EX switches
any solution you got on this. We are also having the same issue with JNPR_RSVD_FILTER_CWA filter and trying to redirect to the OnGuard page for Unknown posture status. We are using Junos: 15.1R7.9...
View ArticleRe: Error when login via console
Hi HDawood, Does it take input at this prompt, or is it just struck there ? Try the below steps from the KB if it takes input and let us know the results:[Upgrade EX switch] – Troubleshoot upgrade...
View ArticleMulticast Configuration for Crestron NVX Equipment
We are implementing an A/V over IP solution from Crestron with the NVX products. Crestron provided our A/V company with a sample single-switch Cisco configuration as well as a guide to network design....
View Article