I've attmpted to follow the documentation but I found 3 different documents stating 3 different ways to create them. I haven't had luck with any of them. I'm to a point where I believe it created virtual Interfaces:
Interface Admin Link Proto Local Remote
ge-0/0/0 up down
ge-0/0/0.0 up down eth-switch
pfe-0/0/0 up up
pfe-0/0/0.16383 up up inet
inet6
pfh-0/0/0 up up
pfh-0/0/0.16383 up up inet
ge-0/0/1 up down
ge-0/0/1.0 up down eth-switch
ge-0/0/2 up down
ge-0/0/2.0 up down eth-switch
ge-0/0/3 up down
ge-0/0/3.0 up down eth-switch
ge-0/0/4 up down
ge-0/0/4.0 up down eth-switch
ge-0/0/5 up down
ge-0/0/5.0 up down eth-switch
ge-0/0/6 up down
ge-0/0/6.0 up down eth-switch
ge-0/0/7 up down
ge-0/0/7.0 up down eth-switch
ge-0/0/8 up down
ge-0/0/8.0 up down eth-switch
ge-0/0/9 up down
ge-0/0/9.0 up down eth-switch
ge-0/0/10 up down
ge-0/0/10.0 up down eth-switch
ge-0/0/11 up down
ge-0/0/11.0 up down eth-switch
ge-0/0/12 up down
ge-0/0/12.0 up down eth-switch
ge-0/0/13 up down
ge-0/0/13.0 up down eth-switch
ge-0/0/14 up down
ge-0/0/14.0 up down eth-switch
ge-0/0/15 up down
ge-0/0/15.0 up down eth-switch
ge-0/0/16 up down
ge-0/0/16.0 up down eth-switch
ge-0/0/17 up down
ge-0/0/17.0 up down eth-switch
ge-0/0/18 up down
ge-0/0/18.0 up down eth-switch
ge-0/0/19 up down
ge-0/0/19.0 up down eth-switch
ge-0/0/20 up down
ge-0/0/20.0 up down eth-switch
ge-0/0/21 up down
ge-0/0/21.0 up down eth-switch
ge-0/0/22 up down
ge-0/0/22.0 up down eth-switch
ge-0/0/23 up down
ge-0/0/23.0 up down eth-switch
xe-0/2/0 up down
xe-0/2/0.0 up down eth-switch
xe-0/2/1 up down
xe-0/2/1.0 up down eth-switch
xe-0/2/2 up down
xe-0/2/2.0 up down eth-switch
xe-0/2/3 up down
xe-0/2/3.0 up down eth-switch
bme0 up up
bme0.0 up up inet 128.0.0.1/2
128.0.0.4/2
128.0.0.16/2
128.0.0.63/2
cbp0 up up
dsc up up
esi up up
gre up up
ipip up up
irb up up
jsrv up up
jsrv.1 up up inet 128.0.0.127/2
lo0 up up
lo0.16385 up up inet
lsi up up
me0 up up
me0.0 up up inet 192.168.100.1/24
mtun up up
pimd up up
pime up up
pip0 up up
tap up up
vme up down
vtep up upIm getting [edit protocols rstp]
'interface'
XSTP : Interface ge-0/0/0.0 is not enabled for Ethernet Switching
error: configuration check-out failed.
How do I wipe out what I've done and create 3 vlans 1 vlan being the management vlan that has a IP attached to it?
I'm not sure of the command to show the the config that while in the configure mode.
Thank You
Bryan