LACP across ports on 2 EX3300 switches in a Virtual Chassis
Hello, Is it possible to create a LACP across ports on 2 EX3300 switches in a virtual chassis? If yes, can you provide the steps and commands to create the LACP. I would like the following interfaces...
View ArticleRe: ip-source-guard/dhcp security blocking lease renewals
As I said above, there are conflicting docs about whether this is possible. How is it possible to get something official from Juniper on this? It kinda seem to work. Also, on juniper swithces does...
View ArticleClik here to view.
Firewall filter EX4600
Hi, I want to create some firewall filters on EX4600.I just want network 192.168.11.0/24 talk only to 192.168.12.0/24 and 192.168.12.0/24 only to 192.168.11.0/24. I created this rules...
View ArticleTroubleshooting error message
I have two EX4300 switchs in a stack. When I first got them I had them lincked usinging optic calbles, they are now using the standard stackign cabels, and only xe-0/2/2-3 & 1/2/2-3 are configured....
View ArticleRe: VLAN Configuration Help
This is the port config from the Dell switch: interface Gi1/0/16switchport mode trunkswitchport general allowed vlan add 203-204,209,215 taggedexit All of the switchports are configured the same on the...
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
Anyone? Here are some examples of what I am trying to accomplish.
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
Yes both are possible over a virtual chassis. We do something similar to #2 with PAN firewalls in active/standby states....
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
HI It is not correct, when we are forming a VC the whole switches are considered as single member. If your requirement is to connect 0/0/1 and 0/0/2 to 1/0/1 and 1/0/2 it is not possible. The reason is...
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
Partha, Please check out the 2 diagrams attached in my previous post. I am trying to create a HA between the 2 firewall machines and the 2 Juniper switches. There are 2 firewalls [pfSense] that is...
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
I have included these 2 new diagrams to hopefully explain what I am trying to accomplish. Please provide the CLI commands to accomplish the LAGG setup in diagram 1 and 2.
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
Anyone? Please help....
View ArticleRe: layer-2 siwtching and logical tunnels
i got it to work.... I was able to add lt interface (logical tunnel interface) as layer 2 interfaces into a routing-instance virtual-switch bridge-domain and then add irb on each logical system and...
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
I know someone can help me... Anyone?
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
Hi, The configuration was already provided. Option 1 set chassis aggregated-devices ethernet device-count 3 set interfaces ge-0/0/22 ether-options 802.3ad ae1 set interfaces ge-1/0/22 ether-options...
View Articleinterfaces interface-name vlan-tagging
Can anyone explain the purpose of the vlan-tagging statement under interfaces interface-name ? The documentation says it exists "to enable the reception and transmission of 802.1Q VLAN-tagged frames on...
View ArticleProblem with Juniper SFP "CM_JAVA [FPC:0 PIC:1]: Failed to uplink SFP 1 EEPROM"
Hi All, we have a switch that is constantly spamming the following messages:Apr 13 13:00:29 sw04.hil.uto chassism[1227]: XCVR: XCVR 1 EEPROM read FailedApr 13 13:00:29 sw04.hil.uto chassism[1227]:...
View ArticleRe: Problem with Juniper SFP "CM_JAVA [FPC:0 PIC:1]: Failed to uplink SFP 1...
Hi, You do not indicate; -Type of EX switch-Junos running-Type of compatible optics The e-prom is probably wrong coded in the optics, please run: show chassis hardware and indicate what you get on the...
View ArticleRe: LACP across ports on 2 EX3300 switches in a Virtual Chassis
GLO, in your 2 diagrams, one.jpg is NOT possible, you MUST use 2.jpg. The 2 FWs do NOT act as one device, which would be required for one.jpg. Instead the act as 2 separate, but redundant devices....
View ArticleRe: Problem with Juniper SFP "CM_JAVA [FPC:0 PIC:1]: Failed to uplink SFP 1...
Hi MICDUF, Pardon me for not excluding the information, i've added it to the origina post.Aas for the output of the show chassis hardware command:REV 01 740-011614 VE134100217 SFP-LX10 We use...
View Article