Clik here to view.
Re: Upgarde proccess for Ex switchs
First, [any] X release is typically associated with a specific product line. I believe 12.3X54 is specific to ACX. There are a few X trains for SRX. X trains were done for new feature velocity (time to...
View ArticleRe: Weird problem.
Also check to see if there is an re-protect firewall filter applied to the EX so that connections from SSH/https are only accepted from certain subnets.
View ArticleRe: Huge latency between two ex switches
Can you run the ping test with the source or interface option to insure the source address of the ping test is coming from the connected interface. ping ping 10.124.53.10 source 10.124.53.9orping...
View ArticleRe: Upgarde proccess for Ex switchs
Hi, Ok i understand the reason why not upgarde, but i still have some questions 1. If 21.3 is the most standing version why juniper recomanded version is 15.1 ?2. Can you explain (in details) me why...
View ArticleRe: Upgarde proccess for Ex switchs
1. Recommendation change to 15.1 was done, then Juniper started seeing issues with 15.1. There is a KB out specific to EX2200 to NOT run 15.1 on this platforn. I [personally] am recommending not to...
View ArticleNew to Juniper, EX3400 VC stack setup help
Brand new to Juniper. Have a very basic setup. Cisco router, 4 ex3400 that I have setup as a VC. Just need help getting the VC to communicate out to the cisco router (192.168.1.1). Everything in...
View ArticleSetting up Isolated VLANs for Guest Wifi
Hello, Newer to JUNOS. Trying to set up an isolated VLAN for a guest WIFI network. the APs have 2 SSIDs installed and the guest network traffic should be going to a tagged VLAN, the other SSID is just...
View ArticleRe: VC-Ports on QFX5110
17.3R1 is releasedRocketRhino wrote:is 17.3 still on track for release at end of August???
View ArticleRe: New to Juniper, EX3400 VC stack setup help
Hi, I am assuming that you have configured a 4 member VC using EX3400.In this case you may need to configure below steps for a basic connectivity. a. Configure same vlan on EX3400-VC :set vlans test...
View ArticleRe: EX4600: multicast not working in vlan default.
I don't need tyhe IGMP snooping at all. I've investigated it as a possible root cause of the non-working VRRP, and it's not it. And what's wrong with default vlan ? It's a regular vlan after all.
View ArticleFusion
Hi everyone I want to use fusion in mx80The satellite device is ex43001.which version to use on mx?I tried 14.2r7 and there are some bugs16.1 no request support information issuePlease assistRegardsOren
View ArticleRe: Setting up Isolated VLANs for Guest Wifi
Which Juniper switch and version of Junos are you running? Typically a WAP will connect to an EX port set to trunk mode.The native VLAN id will generally be the management network for the WAPEach SSID...
View ArticleRe: Huge latency between two ex switches
Probably you faced with the problem described in PR1164135Title QFX5100/EX4600: ICMP latency when pinging to and/or from directly connected l3/irb interfaces...This is due to a hardware limitation....
View ArticleClik here to view.
Re: Setting up Isolated VLANs for Guest Wifi
I much suggested a better approach would be to contact your WLAN vendor and ask them what is best way for network to be set-up to support your specific config/design, and then configure the network as...
View ArticleEX-4600 irb switching / routing / reflection / one-armed issue
I'm attempting to move inter-vlan routing on my ex-4600, but have run into the following (simplified) Switches -EX-4600 "core"which is connected with aggregated ethernet connections to bothEX-3400...
View ArticleRe: EX-4600 irb switching / routing / reflection / one-armed issue
Is the desktop configured with 10.86.0.1 as its default gateway?
View ArticleRe: EX-4600 irb switching / routing / reflection / one-armed issue
Yep -- gateway is set correctly and routing nicely ACROSS switches, but not BACK to the same edge switch.
View ArticleRe: EX-4600 irb switching / routing / reflection / one-armed issue
Can you see if both PC's (laptop/desktop) IP's and MAC addresses are in the ARP table on the EX4600. "show arp"
View ArticleRe: EX-4600 irb switching / routing / reflection / one-armed issue
AAAAND... yet another "make sure firewalls aren't turned on on your devices" issue. Blerg and it's all working now!
View ArticlevQFX MC-LAG not working!
tried a few versions, and I can't get the data-plane to work i.e arp-request gets to either of the MC-LAG pair but they never reply to the host, also the "show iccp detail" keeps bouncing from up to...
View Article