EX 200 and Scheduler priority
Hi everyone, On EX 200 we have only two scheduler priority Strich High and low. My question can I use two traffic classes T1 and T2 with rate limit with both STRICT HIGH ? Basicaly I would EX to do...
View ArticleRe: EX 200 and Scheduler priority
Yes you can, you have to configure queues shaping to avoid lower priority queues starvation.An example borrowed from:...
View Article2 qfx5100 vcf?
A little background before I crack into it: I just started a new job, and my past experience was with cisco adtran etc. The last network engineer left the week I started here, so I don't have a lot of...
View ArticleConsole access is not available on CON port of qfx5100-24Q
Hi Experts, There are two qfx5100-24Q leaf switch and the current configuration is below in my lab.I can access to one of switch via CON port directly. This is fine. But the other switch is not...
View ArticleRe: 2 qfx5100 vcf?
Hi Jason, Yes, you need to have same version on both switches for creating virtual-chassis(VC).Virtual-chassis Fabric(VCF) is incorrect terminology in this case as VCF is spine and leaf topology and...
View ArticleRe: Console access is not available on CON port of qfx5100-24Q
Connect to the console port on the "dead" switch and do a power cycle while watching the output. There should be some useful messages during the boot process that will give a clue as to the nature of...
View ArticleRe: Console access is not available on CON port of qfx5100-24Q
You can also connect to member 1 from member 0 withrequest session member 1
View ArticleRe: EX 200 and Scheduler priority
Can we do the same on SRX with traffic class being STRICT HIGH?
View ArticleGBIC Warranty
I have a Juniper Networks SPP5100SR-J3740-021308 REV 01 10GE SFP+SR that has stopped working, are these devices warrantied from Juniper.? Or just trash it and buy another.?
View ArticleRe: 2 qfx5100 vcf?
ok so one more question i see that i can download directly to the switch witch is pretty cool. but i dont know what file to grab Install Media or Install Package and then im guessing also grab the...
View ArticleRe: GBIC Warranty
There is a one year warranty and as I understand it, they are also covered via the switch/routers support contract. Check warranty status via...
View ArticleRe: 2 qfx5100 vcf?
You will need install package - install media is for USB installation during bootup. Install packages are for online upgrades/downgrades.Just grab the image with enhanced automation which gives...
View ArticleRe: Console access is not available on CON port of qfx5100-24Q
Hi Spuluka, Thanks. Unfortunately there was no output from problematic switch while power cycle. Attached, please refer to a photo I took right after power cycle. As you see from upper side switch, SYS...
View ArticleRe: Console access is not available on CON port of qfx5100-24Q
Hi Smicker, Thanks! It didn't work whereas it did work for own switch (member 0). {master:0} admin@Juniper-L> request session member 1 connect to address 128.0.0.17: No route to host Trying...
View ArticleUpgrade firmware switchEx3300
Dear Sir/Madam I have a Switch EX3300 using firmware 12.3R3.4. But there is some errors CVE existed in this version, so I want to update it to 12.3R12. However,in my equipment has options the layer 3...
View ArticleRe: Upgrade firmware switchEx3300
Hi Folks,Are you planning to upgrade the Junos or only the FPC Firmware? You should not lose layer 3 function in either way. License should not get affected in general. Proactively you can take a...
View ArticleRe: Issues with firewall filter on Juniper EX4550
Hi Folks,In general firewall filters are most rigid in Junos and hitting a BUG is something rare. I would recommend to add specific term to accept followed by specific term to deny and count to...
View ArticleRe: Console access is not available on CON port of qfx5100-24Q
I think you can safely assume the unit is defective and should be RMA’ed.
View ArticleRe: Storm Control on trunk interfaces ?
interpietz wrote:Is it possible to configure storm-control to a trunk-port ?Yes It is. {master:0}[edit]root# show interfaces ge-0/0/1unit 0 { family ethernet-switching { port-mode trunk;...
View Articleallowed mac address on trunk port EX4550 juniper switch
Hi Allkindly assist me on the issue i am facing when trying to configure allowed-mac-address on trunk port, i a getting below error #commit check[edit ethernet-switching-options secure-access-port]...
View Article