Re: EX2200 (Junos 15.1R6.7) Routing-instance doesn't work?
The ex2200 does not support filter based forwarding where you can forward traffic based on criteria like source address or port. The ex2200 does support virtual router routing instances where you can...
View ArticleSNMP OID to get trunk port status - different on a EX2300 vs EX3300 -...
I successfully scan EX3300 and EX2200 switches to get MAC address information via SNMP. Part of that process is to get trunk port status using:...
View ArticleRe: SNMP OID to get trunk port status - different on a EX2300 vs EX3300 -...
Do you have a JTAC case open?
View ArticleRe: SNMP OID to get trunk port status - different on a EX2300 vs EX3300 -...
No. I have not. For a couple of reasons.1. It seems like it should be something that someone has run into and solved(?).2. Opening JTAC cases is a bit of a pain for us since we have to open it through...
View ArticleRe: Fusion
Hi Oren Please find the link below which has the recommeded Junos version for both MX and EX when it comes to Junos Provider Edge solution....
View ArticleRe: Junos Fusion Data Center Technical documentation.
Hi Rskarkey Please find the link below explaining the Junos Fusion datacenter solution, the last link is the configuration guide....
View ArticleRe: Upgrade path for EX4200 stack running 12.3R9.4 to 15.1R6
Hi Joshbaird Please find the recommended upgrade path below. 12.3R9.4 to 12.3R12.4 to 15.1R6-S2 ThanksArul
View ArticleRe: Juniper QFX Models - Port Speed Variations
Hi Wendohw QFX5110-48S: 48 1GbE; 48 10GbE; 4 40GbE; 4 100GbE https://www.juniper.net/documentation/en_US/release-independent/junos/topics/reference/specifications/port-panel-qfx5110-48S.html ThanksArul
View ArticleRe: EX3300 booting & login message
Hi a525 Did you try to format install the switch ? https://kb.juniper.net/InfoCenter/index?page=content&id=KB20643 Please follow the above KB for format install and let us know the results....
View ArticleClik here to view.
Re: MC-LAG with 4 leafs
HI Anbuk Under IP-CLOS Fabric architecture, we will not have any Spine to Spine connections. Please find the solution's recommended topology....
View ArticleRe: Fusion
You may either go with 17.2R2 or 16.1 R5 for stability purpose being the second and fifth regression respectively. Also currently since, Juniper has not recommended any OS for fusion as of now.
View ArticleRe: SNMP OID to get trunk port status - different on a EX2300 vs EX3300 -...
Since Juniper deleted the jnxExVlan mib from Junos on the newer EX platforms, you have to use only standard Q-BRIDGE-MIB OIDs: .iso.org.dod.internet.mgmt.mib-2.dot1dBridge.qBridgeMIB To get the list...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
I know this is an old thread, but check out this funny bit: From...
View ArticleRe: MC-LAG with 4 leafs
Anbuk, as per some of my other responses, you really should be discussing this question with whomever you purchased your Juniper equipment from, or additionally your local Juniper account team. MC-LAG...
View ArticleRe: Connection between Ex4300 and MX security appliance
okay, my mistake was creating V10 as L3 on Ex4300 and that in connection of trunk on both ends EX4300+MX kills the network. I have delete L3 v10 - interfaces irb unit 10 - 192.168.10.1/24 already...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
For any VC license deployment you always need EXACTLY 2 licenses which should be load on Master and Backup switches that act as REs. Of course pre-provisioned VC setup makes this much easy to control.
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
Rccpgm, That's not complete true. With the introduction of the EX2300 series, you actually need a license per EX2300 to operate them in a VC. Then feature licenses are added on master and backup RE if...
View ArticleEX 2200 firewall filter blocks everything
Hello.The task is allow traffic from hosts1 (192.168.1.5) to host2 (192.168.1.10) and block any other.When set filter firewall { family ethernet-switching { filter Allow {...
View ArticleRe: EX4550 lots of mac learning and delete within 2 sec
I see a similar issue in some EX4550-23Fs here.A client has 4 of them in a ring, and we can see the exact same problem. This is with 15.1R3.Suddenly, the switches start deleting and re-learning...
View ArticleRe: EX 2200 firewall filter blocks everything
That is the nature of the firewall filters. "If none of the filters match the traffic, it then applies the default action. Note: Bydefault, each firewall filter ends with an implicit deny-all term. The...
View Article