Re: EX 4600 FBF config
Thanks for your response. Was able to do the FBF using instance import in routing policy.
View ArticleRe: SFP not showing up in config EX4500
SFPs are hot swappable units..Hence you do not need to reboot the Juniper device to have it detected.. Are they third party SFPs? or Juniper supplied ones? On which port are you connecting them? Share...
View ArticleRe: pure L2 multicast traffic (no multicast ip traffic) not forwarded
Here you are an example of MINT traffic.As you can see is pure L2, no L3 address or L3 multicast address. Could you better explain the function of L2 querier ? I can not understand how a querier that...
View ArticleRe: pure L2 multicast traffic (no multicast ip traffic) not forwarded
The mint packet https://www.dropbox.com/s/41iyistkcy72zu3/mintL2.pcapng?dl=0
View ArticleRe: SFP not showing up in config EX4500
Model: ex4200-48tJunos: 15.1R5.5JUNOS EX Software Suite [15.1R5.5]JUNOS FIPS mode utilities [15.1R5.5]JUNOS Online Documentation [15.1R5.5]JUNOS EX 4200 Software Suite [15.1R5.5]JUNOS Web Management...
View ArticleRe: SFP not showing up in config EX4500
I might suggest you try either 12.3R12-S6 or 15.1R6-S3 releases and then see what happens from there. Not use reporting anything with 15.1 that is below 15.1R6-S2 I believe.
View ArticleThoughts On CoS Settings On Edge Switches?
We had a vendor come in and help setup our environment, and since I'm basically a noob when it comes to this stuff (though did try out some setting changes) I'm asking for your assistance. I've never...
View ArticleRe: Thoughts On CoS Settings On Edge Switches?
Looks fine to me other than the strict-high priority. I would personally avoid strict-high because you can starve other queues. How are you classifying traffic?
View ArticleRe: pure L2 multicast traffic (no multicast ip traffic) not forwarded
Huh, it's a unique ethertype. Wireshark 2.4.1 knows what it is but 1.8.3 doesn't. Oddly, even though the newer Wireshark knows what it is I can't find where it was assigned. IEEE page shows 8700-8710...
View ArticleRe: pure L2 multicast traffic (no multicast ip traffic) not forwarded
Hi Chad, Mint was created by Motorola wireless division, or better, by Symbol. Then the wireless solution was acquired by Zebra and at the end by Extreme Networks. The option of configuring the...
View ArticleRe: Thoughts On CoS Settings On Edge Switches?
Thanks for the tip! .. is that because it gets unlimited bandwidth when its set to strict-high? I believe I read that on the Juniper site. Not sure how we are classifying traffic, how would I find this...
View ArticleRe: pure L2 multicast traffic (no multicast ip traffic) not forwarded
I recommend opening a case with JTAC if you can. I'm losing my test environment shortly so I'm not going to be in a position to replicate the behavior for JTAC. From poking around it looks like this...
View ArticleConfiguring EX4200 default static route to cable modem
Hello All, I'm completely new to JUNOS, and I came across an EX4200-24P that I'm trying incorporate into a small home office network. I cannot figure out how to configure a default static route to a...
View ArticleRe: Configuring EX4200 default static route to cable modem
Hi,Can you try below command and check if it works for you?set routing-options static route 0/0 next-hop ge-0/0/0
View ArticleRe: Routing provider's VLANs with EX2200
I'm sorry but this is not clear to me: At the HQ there are 1 cable from the provider and it's connected to Juniper EX2200 JunOS 11.4R1.6 at port ge-0/0/23. Port ge-0/0/4 is connected to the LAN of the...
View ArticleRe: How can I clear RSTP topology changes counter
tty sure this is the only spanning tree clear option, not sure if it does topology changes. clear spanning-tree statistics interface all
View ArticleRe: Interface list disapear
Were the results normal before the configuration was applied? This could be either a hardware or config related problem. With the config there would likely be something in the way a virtual chassis...
View ArticleRe: Authenticate EX4300 with Cisco ACS server
Do you have authentication order setup? https://www.juniper.net/documentation/en_US/junos/topics/example/security-authentication-order-configuring.html
View ArticleRe: How can I clear RSTP topology changes counter
Thank you Steve, Unfortunately, it does not. In 4300 there is option clear spanning-tree topology, but 3300 is missing and clear spanning-tree statistics interface all leave topology changes intact....
View Article