Re: set virtual-chassis command is not working for me on EX4200
Hi, Please make sure you are in [edit virtual-chassis] hierarchyabc123 is serial number of switch, Regarding the serial number of switch, please get it from show virtual-chassis status. Regards,Ajo...
View ArticleRe: Is "Backup" role required if I only have two switches?
Hi, You may set the member role as linecard. Then that member wont be backup /master anymore. Regards,Ajo Thomas
View ArticleRe: Is "Backup" role required if I only have two switches?
Hi, Hope this documents helps :https://www.juniper.net/documentation/en_US/junos/topics/example/virtual-chassis-ex4200-preprovisioning.html Regards,Ajo Thomas
View ArticleRe: set virtual-chassis command is not working for me on EX4200
did you specify "preprovisioned"Specify the preprovisioned configuration mode:[edit virtual-chassis]user@SWA–0# set preprovisioned regardsAlexander
View ArticleRe: How to verify MAC-Move or Enable MAC-Move logs
So guys i tried this on new QFX switches and it bunmped everything BFD,ISIS and BGP ; NOT Recomended > configureEntering configuration mode set vlans Private_Wi-Fi1 switch-options mac-move-limit 1...
View ArticleRe: set virtual-chassis command is not working for me on EX4200
Yes. I did. See below the commands I tried. root@:RE:0% set preprovisionedroot@:RE:0% set virtual-chassis member 1 serial-number BM0211335826 role line-cardset: Syntax Error.root@:RE:0% set member 1...
View ArticleRe: Is "Backup" role required if I only have two switches?
I did follow the steps in the doc you mentioned.See below the commands I tried.I ran these commands when the Matser one is powered on and the second switch is powered off as it is mentioned in the doc....
View ArticleRe: set virtual-chassis command is not working for me on EX4200
you are logged in as root. You need to start the Junos cli via the 'cli' command and then enter the set commands in configuration mode.this mode is accessed by entering the 'configure' command, then...
View ArticleReplace HP QinQ with Juniper EX4300 Q-in-Q
I have a HP Switch that currently have 7 SVLANS on it. Each SVLAN is mapped to a physical port(Customer). Some SVLANS are mapped to multiple physical ports. I am trying to replace the HP Switch with a...
View ArticleRe: Is "Backup" role required if I only have two switches?
You are not in CLI or edit mode: root@test:RE:0% cli {master:0} root@test> edit Entering configuration mode {master:0}[edit] root@test# set virtual-chassis preprovisioned {master:0}[edit] root@test#...
View ArticleQFX5100 scale with EVPN+VXLAN
I'd like to understand the scale limitations on QFX5100 when using EVPN+VXLAN.From my testing i see that any MAC entry in the EVPN database is also inserted into the mac-address table. For example,...
View ArticleRe: Flapping VSTP on a single port
Hi,I did get an confirmation from JTAC that there is an issue with certain IOS releases. But from what I understood, there was no fix available and the root cause was not identified.We rebuilt the...
View Articleno-auto negotiation on EX4550 Juniper switch
hi Alli need you advice on below issue. i want to limit speed on interface ge-0/1/3 to 10Mbps, but this command set interfaces ge-0/1/3 ether-options speed 10m, has no impact as i am still seing...
View ArticleRe: no-auto negotiation on EX4550 Juniper switch
if you disable auto-negotiation , you should do this on both side of link.
View ArticleRe: Replace HP QinQ with Juniper EX4300 Q-in-Q
This is what I have so far. This would be on the service facing side. It doesn't appear that I have the following command and still trying to figure out how I could create a trunk for the customer side...
View ArticleRe: Is "Backup" role required if I only have two switches?
Thank you so much for pointing it out! I am able to change the Backup role to line-card!Next, I'll be testing my switches...
View ArticleRe: set virtual-chassis command is not working for me on EX4200
I'm a newbie here! Thank you for the info!
View ArticleRe: Discarding uncommitted changes
The sort answer to your question is yes, exiting config before committing will discard the candidate config. The answers given below are the cleaner way to achieve what you are asking though.
View Articlenonstop-upgrade on mixed VC EX4300 and EX4600
I'm hoping to understand the real world behavior of using request system software nonstop-upgrade on a mixed VC of EX4300 and EX4600 switches. For a time I know that was discouraged (or just plain...
View ArticleRe: nonstop-upgrade on mixed VC EX4300 and EX4600
If I read this documentation correctly, NSSU is not supported on a EX4600/EX4300 mixed VC: https://www.juniper.net/documentation/en_US/junos/topics/concept/nssu-ex-series.html The page is updated back...
View Article