Re: Delete Not Present switch from VC
Hello thereSee if this command helpshttps://www.juniper.net/documentation/en_US/junos/topics/reference/command-summary/request-virtual-chassis-recycle.htmlHTHThxAlex
View ArticleRe: Failover mc-ae interface
I think this is what you are looking for request interface mc-ae switchover https://www.juniper.net/documentation/en_US/junos/topics/reference/command-summary/request-interface-mc-ae-switchover.html
View ArticleRe: Domain-Type Bridge / Switching on MX series
I see bridge domains used to connect different vlan tagged interfaces into the same broadcast domain at layer 2. So you can have different vlan tags arriving on the same or various ports. and the...
View ArticleRe: Failover mc-ae interface
That command is for MX, I Don’t think this command will work on EX.Hi Krishna,Can you confirm which device are you trying to run this command? MX or EX and which model?
View ArticleTrunk VLANS on EX4300 Uplink Port Configuration
Hey all, This is my first Juniper switch and I've done a lot of learning the last couple of days. I have worked with Adtran and cisco switches in the past. I have 2 EX4300 switches configured in...
View ArticleRe: Failover mc-ae interface
It's an EX9204.root@SW-01> request interface mc-ae switchover mcae-id 2 error: command is not valid on the ex9204 root@SW-01> request interface mc-ae switchover mcae-id 1 error: command is not...
View ArticleEX filters - performance
Does firewall filters / ACLs on EX (3400, 4300 etc.) can affect data plane performance / bandwidth or forwarding latency? Does it matter how complex they are and what actions they perform? (I am aware...
View ArticleRe: Trunk VLANS on EX4300 Uplink Port Configuration
Hi, I am little confused with your requirement. But i beilive you are looking for a connectvity through vlan2 and would like to use it for switch management. In this case you may assign an IP address...
View ArticleRe: Failover mc-ae interface
Hi, As far as I know, this function is only available on MX for now. However i will recheck if similar command was added for EX as well and let you know.
View ArticleRe: Failover mc-ae interface
well one way for sure is to go in and disable the active interface. Not 100% sure why you are using active-standby, vs active-active, but that should work for 100% sure. After disable, delete the...
View ArticleConfigure STP in EX4300 switches
Hello Experts, Since I am relatively new to Juniper world, I am not fully confident how to configure STP in Juniper switches. Can anyon please give me some advice on enabling STP on 2 switch EX4300...
View ArticleRe: Configure STP in EX4300 switches
Hi,The default is RSTP on juniper. You can follow the below link for the...
View ArticleRe: Configure STP in EX4300 switches
Ok.. I just did a quick search. Both VSTP and PVST+ are interoperable. you can use VSTP as well if you wish.
View ArticleRe: Configure STP in EX4300 switches
VSTP was delveloped by Juniper to provide inter-operability with Cisco PVST+. For R-PVST+ interoperability, enable both VSTP and RSTP on the interface - yes this combo is allowed. If plan is to...
View ArticleRe: SFP ports in EX9200 Routing Engine
Short answer is no. I believe none of the SFP+ interfaces on any RE (regardless of product family) are useful at this time, but I also believe the design was for direct access to Control Plane (and...
View ArticleRe: Configure STP in EX4300 switches
So these commands are what I need to achieve the goal. [edit protocols] user@switch# set stp interface all [edit protocols vstp] user@switch# set interface all This will enable both RSTP and VSTP in...
View ArticleRe: Configure STP in EX4300 switches
No. Do not use "set stp interface all". Instead use "set rstp interface all", if you want to interoperate with Cisco R-PVST+.
View ArticleRe: Configure STP in EX4300 switches
Using stp key word enables [standard] STP. For Rapid-STP use key word rstp.
View ArticleClik here to view.