Re: Connecting EX4600 to an EX4300 via 40GbE DAC -- NO VCP
HiThanks for the response ... Neither the 4300 nor the 4600 have VC enabled ... both are disabled.
View ArticleRe: Connecting EX4600 to an EX4300 via 40GbE DAC -- NO VCP
To be clear, even if you've disabled (or not even configured) virtual-chassis in your config, ports will remain virtual chassis uplinks if configured that way. If you've confirmed with the show...
View Articleex2200 fail to boot need your help please
one of my Ex2200 was having an alarm where /var file system is full due to the large size of the WTMP file which is consists of login records i clean up the system after which i rebooted the switch...
View ArticleRe: Connecting EX4600 to an EX4300 via 40GbE DAC -- NO VCP
I love you! That was it! Thanks so much, you're the best!
View ArticleClik here to view.
Cant ping across switchs on managment IP.
Hi All, setup looks like this:SW2.....>SW1......>SRX (attached detailed diagram to this post.) using IRB.60 on both switches and mngt vlan is setup with trunk ports addedd. i have the gateway for...
View ArticleRe: Cant ping across switchs on managment IP.
What does the routing table on sw2 look like? show route I suspect you need a default route from sw2 pointing to sw1 installed.
View ArticleRe: Cisco CDP phones working on EX ELS switches
Could I get a copy of your pcap so I can compare my capture?Thanks
View ArticleClik here to view.
Ex4200 console port issue
I have 2 EX4200 for my lab so no support.. First I can put both switches in a viryual chassis and they seem to work OK..But the 2nd switch console port is dead..Even if I break the VC..Here is what I...
View ArticleClik here to view.
Re: LLDP_Multicast traffic doesn't flow throgh the EX2200
Yes, it was enabled.I switch both interfaces off ( the one which uses PC and the one which uses the PLC) and it doesn't work. This is what i see when i capture traffic in the mirrored port. The traffic...
View ArticleRe: Cant ping across switchs on managment IP.
Hi Steve, put default route in SW2, still ping failing. show route from all three devices:SW2:sh route0.0.0.0/0 *[Static/5] 00:09:33> to 10.2.2.10 via irb.60 10.2.2.0/24 *[Direct/0] 1d 19:23:26>...
View ArticleRe: ex2200 fail to boot need your help please
Hi fadyah1991, How did you perform the cleanup? Was it done manually? //Nexon
View ArticleRe: Juniper EX9200 packet buffer size ?
Hi amarprsi, The buffer capacity usually depends on the type of the line card. By default the buffer capacity is 100ms for ports 1g and higher for an Ethernet port which is distributed to the queues...
View ArticleRe: ex2200 fail to boot need your help please
Hello, Did you check this link? https://kb.juniper.net/InfoCenter/index?page=content&id=KB31245&cat=EX_Series&actp=LIST Regards, Rushi
View ArticleRe: Ex4200 console port issue
Hello, Without support, there are limited options. Most likely hardware issue.It does not sound related but you can try to zeroize the configuration or snapshot it with working device. Regards, Rushi
View ArticleClik here to view.
Re: Ex4200 console port issue
I know, borrowed from a vendor so if can't fix I can buy faiurly cheap.I was thinking about taking a snapshot of a wqorking switch and booting the broke one to USB? Will it over write everything...
View ArticleRe: Cisco CDP phones working on EX ELS switches
I posted the file but its not showing up.. if it doesnt soon .. you can email me.. tom.greaser at gmail
View ArticleRe: Brand new out of box QFX-5110-32Q no interfaces
Try a different version of code.I had the same issue on 17.x code with a qfx5100.After 20 minutes of running no interfaces.Multiple reboots and no change.Don't know how this gets past qa?
View ArticleRe: Brand new out of box QFX-5110-32Q no interfaces
For QFX5K I would highly recommend ONLY running 14.1X53, for which there is a new D47 version. The only exception is if some form of EVPN/VXLAN is required, and then (I believe) you need 17.3 or...
View ArticleRe: Cant ping across switchs on managment IP.
From the output it looks like the SRX is 10.2.2.1 and serves as the default gateway for the subnet. If so, this route should point to 10.2.2.1 not 10.2.2.100.0.0.0/0 *[Static/5] 00:09:33> to...
View Article