Re: Brand new out of box QFX-5110-32Q no interfaces
Guys, seriously--add some optics. Interfaces don't show up without them. Interfaces configured:test@test> show configuration |display set |match "et-0" set interfaces et-0/0/48 ether-options 802.3ad...
View ArticleMSDP MSDP Originator ID and Dense mode region on EX 4300
Hi everyone, 1)Usually MSDP peers are used to connect separate IP PIM sparse regions/domains. In Cisco we can overrwrite that behavior:(10.10.10.10-SRC---R1--PIM...
View ArticleRe: MSDP MSDP Originator ID and Dense mode region on EX 4300
Hello,MSDP is not supported on EX4300https://www.juniper.net/documentation/en_US/junos/topics/concept/multicast-msdp-overview.htmlSupported PlatformsEX4600M SeriesMX SeriesOCX1100QFX SeriesQFabric...
View ArticlevQFX 18.1R1.9 PFE.
Hi All, Does anyone tried latest vQFX release 18.1R1.9 ? Seems to be Juniper supplied second copy of RE image instead of PFE.Isn't it ?
View ArticleRe: EX4200 running 15.1R5.5 unable to install J-web due to low free space
Thanks for the suggestion spuluka. Running the Junos from a USB stick would give me enough space to install and run JWeb. However, I have been unable to get a "request system snaphsot media external"...
View ArticleFirewall srx 340 issues
Hello, i have trunk the fibre port (ge-0/0/15)of srx 340 firewall. However , the same donot work. Any suggestions
View ArticleRe: Cant ping across switchs on managment IP.
Hi Steve, Done so. still not pinging. looking at the diagram i have attached now, how else could i manage this swtiches? is this design of cascading the swithes violating some switchig or routing...
View ArticleRe: EX4200 running 15.1R5.5 unable to install J-web due to low free space
It might also be bad internal media which a format install may help. You may want to open a JTAC case to verify the hardware at this point.
View ArticleVideo Services
I am working with a pair of EX3300-48 switches. W have several satellite receivers connected to these for a analog to digital video migration. When using VLC Viewr and the Arris CAP1000 to mintor the...
View ArticleRe: Video Services
ve uploaded the wrong switch configuration, here is the confi I am working with
View ArticleRe: Cant ping across switchs on managment IP.
The daisy chain is unusual but still should work. Often a single switch will connect to the firewall and the other downstream switches connect back to this as a aggregation point. Looking closer at...
View ArticleRe: Trunk port on srx340
Hello, You can try something similar to this. set interfaces ge-0/0/2 unit 0 family ethernet-switching interface-mode trunkset interfaces ge-0/0/2 unit 0 family ethernet-switching vlan members test...
View Articleno fiber connectivity
We recently upgraded our switches, while changing one friday we ran into an issue where one of the fibers did not uplink, we have changed optics in the switch, tested fiber from a to b, changed st...
View ArticleRe: no fiber connectivity
Are you sure the optics match on both ends? DId you try rolling the fiber patch cords on one end?
View ArticleRe: no fiber connectivity
We changed multiple optics out just to make sure that wasnt the issue. What do you mean roll the fiber on one end? Were up for anything to help resolve this issue!
View ArticleClik here to view.
Re: no fiber connectivity
You need to make sure the transmit fiber strand ends up on the recieve side of your far end optic. If your premise cabling and/or patch cord(s) have these strands criss-crossed somewhere then your...
View ArticleRe: no fiber connectivity
We use the pre-termintaed LC connectors at the switches to connect to the optic, they are plugged in correctly. The issue we do not understand is how it quit working after switch change when the config...
View ArticleRe: Cant ping across switchs on managment IP.
Hi Steve, Figured out the problem. it was security zone configs on the SRX. had to add vlan.60 interface under trust zone.can ping all the switches now. thanks for your effort and time. Regards,lish.
View Article