Re: ACX1100 how to set a trunking interface ?
Interface-mode trunk is not supported on acx
View ArticleRe: ACX1100 how to set a trunking interface ?
Hi Diego, What is your exact requirement? Can you open a new thread and share the details?
View ArticleRe: SNMP 1 GB interface
Hi Bhavish, On which Junos you are checking the output? This problem has been fixed in PR/1218134 [KUDOS PLEASE! If you think I earned it!If this solution worked for you please flag my post as an...
View ArticleRe: QinQ Again.
Hi Testdog, You can mark your reply as "accepted solution" so others can get the benefit.
View ArticleRe: IGMP needed on PIM Interface towards source
Hi,Please provide the config and below output:show pim source detail show igmp interface //RegardsAD
View ArticleRe: IGMP needed on PIM Interface towards source
Hi Folks,Some pointers to start your multicast troubleshooting, IGMPshow igmp interface detail | no-moreshow igmp group detail | no-moreshow igmp statistics | no-more PIMshow pim interface |...
View ArticleRe: IGMP needed on PIM Interface towards source
To add, some interesting KB, Resolution Guide - Troubleshoot Multicast issue with Junos OS device configured as Layer 3 (running PIM protocol)...
View ArticleRe: Any way to disable IVR?
Hi Folks,You can try segregating the interfaces into logical systems, if you would like to totally isolate the traffic between them
View ArticleRe: Any way to disable IVR?
To add, not sure if ex-3400 supports logical system/… Need to check it….
View ArticleRe: Creating a VTY ACL
Hi Folks,Just thought of sharing some interested terms you can add in loopback filter…....
View ArticleRe: Creating a VTY ACL
Hi, You can use Cisco to Juniper CLI converter to convert the IOS config: IOS-to-JUNOS (I2J) Conversion Tool - Tool Fact Sheet IOS TO JUNOS TRANSLATOR Below is your converted config in Junos: system {...
View ArticleRe: Juniper EX2200
Hi Peter, When exactly did you see this behaviour?Have you tried rebooting the device to see if it comes up fine?Did you perform any activity like upgrade/downgrade on the device? It seems like there...
View ArticleRe: Juniper EX2200
HiThis message occured after upgrade switch to latest JATC recommended version. Switch is refubrished and I don't know if it has been working before upgrade. Upgrade was the firts thing I'have done. I...
View ArticleRe: Juniper EX2200
Sounds like it might be a hardware failure. Can you run: show chassis alarms And did you see this recommended release information and are running 12.3r12 or less....
View ArticleRe: Juniper EX2200
Could you please try format install once, using below mentioned linkhttps://kb.juniper.net/InfoCenter/index?page=content&id=KB20643
View ArticleRe: Creating a VTY ACL
Hi Nsylaj You can use the below example to allow only certain IPs to ssh to the device. root@QFX#run show firewallFilter: __default_bpdu_filter__Filter: VTYACL Counters:Name Bytes PacketsVTYACL 3360...
View ArticleRe: Any way to disable IVR?
There is no way to disable Inter VLAN routing (IVR) You can put the Mgmt VLAN IRB under an Routing instance.
View ArticleQSFPP-4X10GE-LR @ 40Gb?
Can a QSFPP-4X10GE-LR optic operate as a single 40Gb interface? Or does it work only as 4x10Gb channelized?
View ArticleRe: QSFPP-4X10GE-LR @ 40Gb?
Hi Folks,Based on my understanding QSFPP-4X10GE-LR QSFP+ 4x10GbE can be used as only 10GbE interface and not as a single 40GbE interface. You will need a 4X10G BREAKOUT cable to connect to the other...
View ArticleRe: QSFPP-4X10GE-LR @ 40Gb?
I actually believe the answer is yes, that it can support 40GE (via 4 x 10GE wavelengths) or be used with break-out cable. If you go to Pathfinder here -...
View Article