Re: Upgrade EX4200 version 11.4R75 to 15.1R5
Which 15.1? I am at 12.3R12 and unable to even go to 14. I had assumed this was since 13 is missing.
View ArticleRe: Upgrade EX4200 version 11.4R75 to 15.1R5
For reference I am upgrading from J-Web.I have tried the following all from 12.3R12.14.1X53-D10 and D47 - left with Juno’s Loading - had to rollback15.1R1 and R7 - failed in the same way.
View ArticleRe: How do i configure an ACL for SSH on Ex4200 Switch
There is no VTY line style of setup in "JUNOS" like cisco's vty line access-control except for "JUNOSe S/w" where the CLI is IOS alike & have vty line". In JUNOS we configure firewall filter to...
View ArticleRe: How do i configure an ACL for SSH on Ex4200 Switch
Can i add it to the Management VLAN instead of the Lo0 ? For example:set interfaces vlan unit 1 family inet filter input local_acl set interfaces vlan unit 1 family inet address 10.155.96.5/21...
View ArticleRe: How do i configure an ACL for SSH on Ex4200 Switch
Juniper devices do not have an equivilent to the Cisco VTY. I'm not sure what you mean when you say the device isn't using a loopback interface, as it is the connection between the data plane and...
View ArticleRe: Upgrade EX4200 version 11.4R75 to 15.1R5
For legacy EX products, you can upgrade directly from any 12.3 to any 15.1. There is no need, nor any good reason, to go to either 13.x or 14.x for these products. I have never used J-Web to upgrade,...
View ArticleRe: Creating a VTY ACL
VTY lines are a cisco concept. The loopback interface controls all traffic to the control plane, that includes management, routing protocols, icmp (to the device), etc. Your approach is correct but you...
View ArticleRe: EVENTD high cpu utilization 2300ex vc
Are you still having this issue? We've been fighting it for some time without success. At one point the engineer found evidence that it was the Junos Space VM causing the CPU spikes, but I've turned...
View ArticleRe: VC non-provisioned to pre-provisioned while running
Hi all, since nobody replied i did "harakiri" - it worked.However a reboot is required to switch from non-provisioned to provisioned.Before the reboot the Device with the SerialNumber will be shown...
View ArticleRe: EX9204: MC-LAG
Hi Krishna_85,config-sync in this case is not possible as far as i know but in general you should not see any issues with the way that you described.
View ArticleJuniper EX2200
Hi I have Juniper ex2200-48t-4g [12.3R12.4] and all my ports all physicaly down. If I connect any device to any port the link stays down. Here's the log n 20 08:12:40 chassism[1213]: Port apply config...
View ArticleAny way to disable IVR?
I have several VLANs set up on my switch and I want the routing to occur at the firewall so I can apply security policies between the VLANs. After some research this appears to not really be an easy...
View ArticleRe: Any way to disable IVR?
Hi ,You can put those layer-3 interfaces under different routing-instances.set routing-instance NAME_X instance-type virtual-router interface <interface-name> [KUDOS PLEASE! If you think I earned...
View ArticleRe: vlan-ccc l2circuit from double tagged interface to double tagged interface
Hi, Please refer to the below document : Configuring a Layer 2 Circuit on a VLAN-Bundled Logical Interface [KUDOS PLEASE! If you think I earned it!If this solution worked for you please flag my post as...
View ArticleEX2300 VC on one end, unknown vendor/VRRP on the other
We're getting a set of two ethernet handoffs for a L2 datacenter interconnect from our telecom. They are using VRRP on their end, whereas on our end the two lines are going into two different EX2300...
View ArticleBridge two vlans
Is is possible to join two vlans using a juniper switch/router? vlan10 interface vlan20 interface bridged interface = vlan10 and vlan20 in the same segment I can't use the same vlan because my fiber...
View ArticleRe: Bridge two vlans
One way to do is to physically connect a port from vlan 10 into a port from vlan 20.But this doesnt scale because it requires two physical ports.Does the juniper allow to bridge two same subnet vlans...
View ArticleRe: Bridge two vlans
Hi, Please refer the solution provided in this JNET post: Bridge-domain,multiple vlans and flooding domains [KUDOS PLEASE! If you think I earned it!If this solution worked for you please flag my post...
View ArticleRe: ACX1100 how to set a trunking interface ?
I have the same problem with an ACX5048 could you solve it?
View ArticleRe: ACX1100 how to set a trunking interface ?
What junos version are you running on the ACX? I see the MX version posted above is supported on ACX 15.1 flexible-vlan-tagging;encapsulation flexible-ethernet-services; unit 0 {...
View Article