Clik here to view.
Re: SSH and telnet issue
yes same subnet same vlan, i just thought there is somthing fancy to do with SSH in juniper and i will, thanks for your help
View ArticleRe: SSH and telnet issue
Is there a protect firewall filter applied to the mgmt interface on the switches? Look at the interface configuration that has the ip address you are doing the ssh to as the target. If there is an...
View ArticleRe: SSH and telnet issue
hello Spuluka I'm not using the Mgmt interface, i just created a new vlan named it Mgmt with irb adress and ae interface as trunk this is the way i used to do with Cisco.and i didnt apply any kind of...
View ArticleRe: SSH and telnet issue
What are the return routes on the TOR switches?For the subnet on the laptop that cannot connect where will the TOR send the reply packet
View ArticleRe: SSH and telnet issue
my laptop in the same subnet same vlan, so i didnt make any default routes in TOR
View Articleadd / Insert Vlan to QinQ interfaces
HelloRequest for support,Is it possible to add (injections) to the link on which QInQ (xe-0/2/2 unit 3000) comes out add a regular vlan that enters in a single link xe-0/2 / 0.650 My config: set...
View ArticleRe: EX3300 Autoinstalling a Configuration file from USB
@rccpgm: Many thanks for your response. To configure or change software via console is not use case which I aim at.Use case is that field engineer gets the configuration for USB Memory Stick via...
View ArticleRe: Auto Image Upgrade
I am getting the same errors, however, I cannot seem to do the EZSetup either. I am getting a "Command Not Found" each time.
View ArticlePhone in both VoiP and Data VLANs
I am using Juniper ex4200-48p running JUNOS Base OS boot [12.3R6.6]I have a dot1x environment, using Cisco ISEAll my ports are under dot1x control (via Cisco ISE) and are working as expectedHowever I...
View ArticleReplacing (RMA) or adding new switch to QFX5110/QFX5100 VCF don't work.
Hello I have issue adding new/RMA switch to VFC.Our setup is 2 QFX5110-32Q as spine and various QFX5100-48T/S-6Q as leafs. One of leafs was RMA and also need to add additional QFX5100-48T-6Q as...
View ArticleRe: Phone in both VoiP and Data VLANs
This link shows you how to perform this for non-ELS EX switches: https://www.juniper.net/documentation/en_US/junos/topics/example/802-1x-pnac-voip-no-802-1x-ex-series-configuring.html Hope this helps....
View ArticleRe: Phone in both VoiP and Data VLANs
Thank you for the responseI am interested in why the following configuration, is causing the MAC to appear on both VLANS?Ignoring the dot1x element as its not applicable, as I've removed itIs it...
View ArticleRe: Phone in both VoiP and Data VLANs
I am old and half senial, but I think there was already a thread about this same situation - maybe search for it? If you delete phone MAC from table, is it re-learned in both VLANS, named VoIP and...
View ArticleRe: Phone in both VoiP and Data VLANs
Thanks so much for that, that is exactly what I think is happeningI'll search for that This probably means no impact then
View ArticleRe: Phone in both VoiP and Data VLANs
I would expect normal/expected and no impact as well. Please get back with your findings so others may know for sure as well. Thanks.
View ArticleRe: Phone in both VoiP and Data VLANs
As it stands the phone I am testing on works, despite appearing in both vlans (DATA and VoiP)I have made calls without issueI have rebooted the phone and it comes back up without an issueI am going to...
View ArticleRe: Native VLAN id on Juniper
FYI...the native vlan behavior changes on QFX or ELS junos OS versions -...
View ArticleRe: EX4500 rebooted automatically without proper reason
It is possible that a PEM failure can cause reboot on EX4500 device. Since the 2 power supplies are fully redundant, if one fails, the other should ideally take over. The switch reassesses the power...
View ArticleStack with different revision members - EX4200-48T
Hi, We have STACK with 4 x EX4200-48T switches with hardware REV 18.At the moment we are considering buying one more (refurbished), but it is REV 06. According to the output of the "show chassis...
View ArticleRe: Stack with different revision members - EX4200-48T
Hi,I don't know documentation for that, but I use the different revision number of EX-4200 series as a virtual chassis within two different environments. (REV 23,REV 16- REV 23, REV 15)
View Article