Re: EX3200 vs. Cisco WLC and AP
Hello Please see the working configuration of Wireless setup in Juniper switch as required. Mentioned port have Cisco AP connected and we have Cisco WLC as well in our network. ge-0/0/0 { unit 0...
View ArticleRe: syslog and SNMP traps failing
Hello Please check this working configuration and match with your scenario. syslog { user * { any emergency; } host rivest { any notice;...
View ArticleRe: Rescue-Config - Hostname not set on EX2200
Hi Please try to use hostname with 8 characters or less. Thanks
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Thank You, looks like I have to work with Aerohive to figure their LACP protocol since that should work but its not. lastly i will be testing that by setting cisco switch and comparing to cisco lacp,
View ArticleEX-4200 does not support nested firewall rules?
Hi, all, according to documentation, nested firewall rule is supported on EX-4200 platform, however it does not seem to be the case, any idea? EX4200-24t# set firewall family inet filter filter1 term...
View ArticleRe: EX-4200 does not support nested firewall rules?
Hello, I tried configuring it (even though it does not auto complete), I got following error: root@EX42xx-SUNNY# show firewall family inet { filter test { term 1 { then { log; accept; } } } filter...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Hi, You could also configure the ae without lacp:delete interfaces ae13 aggregated-ether-options lacpThe ae interface would come up but then there would be no control info to signal that the LAG is ok...
View ArticleRe: 4300 LACP for Aerohive Access Point in aggregate mode
Yeap Aerohive230 does not support LACP only AKA Etherchannel ehhhhh
View ArticleRe: Rescue-Config - Hostname not set on EX2200
Our hostnames typically exceed 20 characters and the official max supported is 255 characters. What is the eight character limit a reference from?
View ArticleRe: Rescue-Config - Hostname not set on EX2200
On the second EX2200 the hostname is set correct - i will try to re-image the first ex2200 to check if this was related to a faulty image. But I'm curious now - on some Switches we have hostnames with...
View ArticleDomain bridge ex2400
Hi, I need to connect one router with 1g interface to my mx having only 10g interfaces. I thouht using my ex switch and creating a domaine using one 1g and 10g unused interfaces to do so. Does a simple...
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
Hi guyes,I tried to shutdown interface ae9.0, after that mpls traffic autoimatically swtiched on ae10.0. Automatically changing interface of mpls traffic working fine. But still the question with...
View ArticleRe: Domain bridge ex2400
Hi, If it is an EX, you could do this with a new vlan rather than bridge-domain. Cheers,Ashvin
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
Hi, It seems both LSPs have the same path [interface ae9.0]Can you share ouput:show mpls lsp name to-SPB-REP extensiveshow mpls lsp name to-SPB-REP-2 extensiveCheers,Ashvin
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
user@EX-4200-Stack1# run show mpls lsp name to-SPB-REP extensive Ingress LSP: 2 sessions 10.255.0.3 From: 10.255.0.1, State: Up, ActiveRoute: 0, LSPname: to-SPB-REP ActivePath: (primary) LSPtype:...
View ArticleRe: EX-4200 MPLS CCC load-balance with two links
Hi,Both LSPs are using the same path, hence same egress interface ae9.0.I believe there's 2 options to load balance traffic:1. Configure ERO [Explicit Route Object] for the LSPs, each with distinct...
View ArticleClik here to view.
Configuration Assistance - QFX10008 to EX4300 using JNP-QSFP-DAC-5M
Hi all,I'm trying to connect a QFX10008 to an EX4300 switch using a Passive DAC as uplink port and not as vcp.I already found out that the default behavior for a 4x40G pic in the EX4300 is configured...
View ArticleRe: Configuration Assistance - QFX10008 to EX4300 using JNP-QSFP-DAC-5M
Disable autonegotiation on both sides--this is the only way we can get our 4300's and QFX to link over 40Gb DAC. --Paul
View ArticleRe: Configuration Assistance - QFX10008 to EX4300 using JNP-QSFP-DAC-5M
Hi PaulYou're right, this is the solution indeed.Trying it couple of hours after posting this question only at the 4300 end solved the issue. Thanks a dozan David
View Article