Re: Safe to delete /var/root/vartmp?
Hi, You can use "request system storage cleanup dry-run" to test the file can be removed and "request system storage cleanup " to clean.
View ArticleRe: Safe to delete /var/root/vartmp?
I ran "request system storage cleanup dry-run" again the affected member, and other than a few small log files, it didnt flag this file or anything larger than a few KB
View ArticleRe: Safe to delete /var/root/vartmp?
Hi , Can you confirm if the file path "/var/root/vartmp" is correct ?
View ArticleRe: Safe to delete /var/root/vartmp?
vartmp is the file but the path is correct: root@:BK:9% ls -l /var/roottotal 212592lrwxr-xr-x 1 root wheel 35 Jan 20 2016 .cshrc -> /packages/mnt/jbase/var/root/.cshrc-rw------- 1 root wheel 2157...
View ArticleRe: Safe to delete /var/root/vartmp?
I am not sure what type of file it is however please check what is inside it . cat /var/root/vartmp
View ArticleRe: Safe to delete /var/root/vartmp?
A whole lot of non-text data like: ▒▒V▒*[O▒~eT,K▒▒,<▒g2▒p▒▒_▒L#Y^~▒»g|▒s▒▒▒{▒▒▒▒▒7▒l▒▒▒▒▒▒۠Nz,▒▒̰`▒▒▒▒g▒▒ے▒h▒)8▒▒▒▒▒^%▒T▒▒▒4▒⻊▒▒▒C▒ 8▒h▒▒J▒▒▒OVh▒>e.)▒)+կa.▒▒▒▒▒d▒:▒R▒Ǹ▒▒>B▒...
View ArticleRe: MC-LAG down (QFX10K to EX4550)
Hi Smicker,Just wanted to let you know that this issue was resolved today.1. The issue concerned spanning tree configuration on the 4550 and the 10K at this point the physical status went upand the...
View Articlevirtual chassis with high CPU consume
Hi all, Current we have two EX4500 forms a virtual chassis, and the CPU is very high. The master take about 70-80 percent cpu usage and backup take 40 percent of cpu usage.The process use the CPU are...
View ArticleRe: QFX5100 Error Messages from jdhcpd
I'm getting the same. Did you hear anything? I'm contacting JTAC: jdhcpd: libstats_op_iflstats_using_sec_index: failed the operation (2) from DB, db_ret: -30989, ret:-7
View ArticleRe: EX2200 Host 0 Boot from backup root
Hi! Have you managed to solve this issue? I'm having exactly the same issue, but with ex3300-48t switch and the same 12.3R6.6 junos. I followed all the manuals on juniper site considering this issue,...
View ArticleRe: EX2200 Host 0 Boot from backup root
Hi, what version junos that u use? U just need to configure "set system auto-snapshot" . Then it will do automotaically.
View ArticleExisting switch support for the newly approved 802.3bz standard
Since the IEEE have been working on this spec since 2014, I'm wondering if any Juniper switches currently for sale will eventually support the standard via a JunOS update or will we have to wait for...
View ArticleEX3300 multicast
Hi, I have a single EX3300 and I'm trying to learn MVLAN and/or PIM. Not sure what would work best for my topology, lets describe it: * Single EX3300 switch * Doing L3 routing with OSPF, both IPv4...
View ArticleRe: Existing switch support for the newly approved 802.3bz standard
I'm not up to speed on the standard but every standard before has been an update to the physical layer, I do not belive an 1G port can suddenly be upgraded to 5G with a firmware upgrade.
View ArticleRe: EX2200 Host 0 Boot from backup root
The version is, as I've stated above 12.3R6.6 Why should I care about auto snapshot, if even manual snapshot is not working? It does not matter, how many times I do snapshot to alternate slice, I end...
View ArticleClik here to view.
Ex4500 bandwith policer, filters counters and cpu impact
Hello, I think to deploy my old ex4500 before my bgp router in order to count, limit and or filter out udp floods, bum packets and other stuff connected with ddos flooding. Every isp will be...
View ArticleRe: Safe to delete /var/root/vartmp?
I have never seen such directory , it seems manualy created . You can log a case with tech support.
View Article