Re: EX2200 Host 0 Boot from backup root
Hi romeo.r, Use the alternate statement instead of '1' statement .request system snapshot media internal slice alternaterequest system reboot slice alternate media internalIf still does not work ,...
View ArticleRe: Can't Ping Internal IRB
i cant ping to irb interface say is down, i associate to physical interface but not come up
View ArticleClik here to view.
how to disable the virtual chassis mode on ex4200
Hi Guys! how to disable virtual chassis on ex4200-48t， i try to entering the shell /config/vchassis delete all files and close all vc-port then restart the ex4200“invalid” root> show version...
View ArticleRe: aggregating bridged interface rate policer
This is the method we use on the MX and EX. The documentation does not mention the QFX series so it may not be available there....
View ArticleRe: how to disable the virtual chassis mode on ex4200
In general, do not delete configuration files from the shell directories. This is the rpocedure to remove virtual chassis....
View ArticleRe: EX4300 LACP with SRX requires VSTP Edge configuration. Why.
I can report the following findings / issue. This is confirmed between EX4300 and SRX240.Configure both devices with periodic slow (as per recommendation by Juniper KB).EX4300 as active LACP, and SRX...
View ArticleFlapping VSTP on a single port
Hi, We have a setup with vstp between us and our ISP.The setup connect two separate switches to two switches at ISP side for redundancy.This has been working fine with Cisco and was not moved to...
View ArticleClik here to view.
Re: EX2200 Host 0 Boot from backup root
Hi, thanks for reply. After I do (and I did multiple times already ) this: request system snapshot media internal slice alternate request system reboot slice alternate media internalSwitch reboots from...
View ArticleClik here to view.
Re: how to disable the virtual chassis mode on ex4200
Hello Steve thank you for your helpBut prompt with no change the configration thanks
View ArticleIEEE 802.1p classifier on access mode port
Question: on EX4600 manual, it says:If you configure a Layer 2 logical interface, the system uses the default IEEE 802.1p trusted classifier if the port is in trunk mode or tagged-access mode, or the...
View ArticleRe: IEEE 802.1p classifier on access mode port
Hi, My understanding is that although no vlan tags & no 802.1p bits, packets from access port can be classified into a forwarding class. The default untrusted classifier classifies all access port...
View ArticleUser class settings
I want to use the Operator class of rights for our helpdesk team, do not want them to be able to set, or configure. I want the to have all the rights of the Operator;operatorclear, network, reset,...
View ArticleRe: User class settings
Hi, Please try adding this : set system login class User deny-commands configure Let me know if it works
View ArticleClik here to view.
tried everything - cannot communicate with the EX2200-C
After unboxing the 2200-C, I connected the Mini-USB end to the CON on the front panel. The other end into USB port of my PC running Windows 10.Windows 10 does see a new USB port and gives it COM11 (...
View ArticleRe: tried everything - cannot communicate with the EX2200-C
From a little research, it looks like I may need a db9 ( rs232 serial) Male to USB A ( my PC side).As weird as it may be. the initial connection : RJ45 Con port to RJ45 to DB9 Female to DB9Male to USB...
View ArticleLog message entries
Hello, In log message, i have a lot of lines like this : Oct 4 08:55:26 core.ncp fpc1 VXLAN not found for vlan 40 Rx Port 65 Trunk: No What is "Port 65" ?How to find the correspondence between the...
View ArticleRe: User class settings
Hi, You may need a new class for this:https://kb.juniper.net/InfoCenter/index?page=content&id=KB23038&actp=search Example:> show configuration system login class op permissions [ clear...
View Articleae11 inactive - how to activate again
Experts, Looks like trivial issue:AE11#### inactive: interfaces ae11##aggregated-ether-options { lacp { active; periodic fast; }}unit 0 { family ethernet-switching { vlan { members 101; } }} When I...
View Articlenew vlan not pulling IP from DHCP or able to ping Gateway
I have a EX4200 (11.4R5.7) core switch that connects to an EX2200 (11.4R2.14) via a direct link and that connects to another EX2200 (11.4R1.6) via wireless bridge. The native vlan (VLAN254) works fine...
View ArticleRe: ae11 inactive - how to activate again
You can do this: enter configuration mode with configurethenactive interfaces <iinterface> and commit ..........
View Article