Cisco IP Phone Compatibility?
I'm having an issue where a Cisco 7945G IP phone connected to a Juniper EX4200 will not pull an IP address from DHCP server. When I connect the phone to a Cisco 3750 switch it works fine everytime. I...
View ArticleUpdating J-Web on 4300 - 48 ???
Experts, before I upgrade to You are using J-Web platform package that has limited J-Web functionality. Update to latest JUNOS Web Management Application package [14.1X53-A2.1] to get full J-Web...
View ArticleRe: Hi MC-LAG + VRF ?
Hi, I never tried this, and im planning this for my network development. Thx..
View ArticleRe: Updating J-Web on 4300 - 48 ???
No required downtime.Pl open the session again after few sec, There is no need to reboot the switch after the installation. The J-Web Application package is hot pluggable and installs on top of the...
View ArticleRe: best practice for switch lockdown?
Thank you that was most helpful. One question regarding the use of mac count limiting - ie; set interface ge-0/0/2 mac-limit 4 - if i use this on an interface range rather than a single port, does it...
View ArticleRe: best practice for switch lockdown?
Groups are a short cut to apply configuration to each interface via the single group section. So each interface will behave as if you configured them separately.
View ArticleNoob question Web-Managment Ex2200
Hello And greetings from norway. Im playing around whit my Ex2200 on my lab. Ive managet to get ssh telnet and som functions to work.But im struggelign whit the web managment. i have assigned the ip to...
View ArticleRe: Updating J-Web on 4300 - 48 ???
Thank You Suresh, I am more concern about virtual chasis snice that stack include main MDF and 4 x switches 4300. But if are saying its not going affect anything i will schedule upgarde after hours....
View ArticleRe: Noob question Web-Managment Ex2200
I'm not sure if I got you right .. so correct me if I'm wrong..You're not able to access you switch J-web page ?If yes , what you're typing in your browser? http://<ip-address>:8080 ?Can you also...
View ArticleRe: Problem with vlans merging one core to another core
Steve, IF I take the config, and add new ports, but keep the active ports as they are, then do a load overide.term.Will that cause the switch to drop the active ports for a couple seconds.?
View ArticleRe: Problem with vlans merging one core to another core
When you have the final configuration loaded as the Candidate config do a compare to the running config #show | compare The sections of the config that show the - sign to delete followed by the + sign...
View ArticleVXLAN on DCI question
Hi I have been setting up my QFX5100 IP fabric following this blog: lab-on-evpn-vxlan-on-juniper-qfx5100-switches inside my fabric all works well. I then setup another fabric pod using the same...
View ArticleRe: ae interface shutoff by storm control, how do i see which of its member...
hi, have your tried the command show interfaces ae0.x details extensive ? this would give you details on Date, time, and how long ago the interface went from down to up or from up to down you...
View ArticleRe: Noob question Web-Managment Ex2200
Im sorry my bad. Yes im Trying to reach 192.168.1.8:8080 Whitch is the juniper device. I can see the Juniper divice in the dhcp scoop of my lan but i cant login to the J-web page. time-zone...
View ArticleMACsec on EX3400
Is the level of MACsec support on EX3400 the same (or similar) as on the EX4300? Regards,Pawel Mazurkiewicz
View ArticleRe: MACsec on EX3400
Yes ex3400new switchesare support MacSec, but i am not sure is it same as ex4300 or not.
View ArticleRe: Noob question Web-Managment Ex2200
Hi First, I don't see in the new configuration you shared the 8080 port statement as the first output you shared .This (J-web) should work only if you go through the browser to...
View ArticleHigh multicast
I 4300EX switch inder J-WEB I see the graph with input | output and multicast consumes more than 90% overrall. I have to admint we use apple tv with bonjure gateway as is generating a lot these. I...
View Article