Juniper 2200 EX storm control
Experts, Just started noticing message: ESWD_ST_CTL_ERROR_IN_EFFECT: ae0.0: storm control in effect on the port ae0 is a trunk port to another switch, but show configuration...
View Article4300EX EX-BCM PIC errors
Experts, I have started seeing these messages: Jan 12 13:40:00 BZMDF fpc3 [EX-BCM PIC] ex_bcm_linkscan_handler: Link 46 UP Jan 12 13:39:58 BZMDF fpc3 [EX-BCM PIC] ex_bcm_linkscan_handler: Link 46 DOWN...
View ArticleRe: Juniper 2200 EX storm control
Hi, ESWD_ST_CTL_ERROR_IN_EFFECTThis condition occurs when a storm control error condition is detected. The interface specified in the syslog message has exceeded the threshold for storm control and...
View ArticleRe: 4300EX EX-BCM PIC errors
I think this might be something juniper support might look, since I really cannot find anything.
View ArticleRe: 4300EX EX-BCM PIC errors
Hi, This is a logging done due to some call to the reference value. These log messages are merely informational and not harmful, you can ignore them. You can use the below mentioned technical document...
View ArticleRe: 4300EX EX-BCM PIC errors
Yes I think the log is refering to some ports and flaping issue. But the link is great - Thank You again.
View ArticleRe: 4300EX EX-BCM PIC errors
Hi, If this solution worked for you please flag my post as an "Accepted Solution" so others can benefit..
View ArticleRe: EX4550-32T and VCP
Try to answer some of your questions: 1) is it possible to create a VCP based LAG of 2*10G links between 2 members of a unique VC with 2 different link types :a) 1 link based on SFP+ 10G optical ports...
View ArticleRe: 4300EX EX-BCM PIC errors
Reported observation: “[EX-BCM PIC] ex_bcm_linkscan_handler" messages seen in the box Resolution: These log message “pfex: [EX-BCM PIC] ex_bcm_linkscan_handler:” is informational message which is about...
View ArticleRe: Juniper 2200 EX storm control
Hi Folks,Looking at the log messages,ESWD_ST_CTL_ERROR_IN_EFFECT: ae0.0: storm control in effect on the port ESWD_ST_CTL_ERROR_IN_EFFECT- This condition occurs when a storm control error condition is...
View ArticleRe: EX2200 system overload problems with 15.1Rx upgrades
@Akeskin: We've not yet opened a case still. However there is no typo. We have adopted the 15.1 code pretty early due to some policy saying "you must not use firmware that is going to be EoE" - that...
View ArticleClik here to view.
Inband Management on EX3300
Hi All,I'm a Juniper n00b, so bare with me. I'm setting up inband management and unable to hit the mgmt interface (am connected to the switch directly).I've assigned an IP to a new MGMT vlan;set...
View ArticleRe: Inband Management on EX3300
Hi, i think your problem is that you have created a vlan "MGMT" with vlan-id 10 and then another vlan named "mgmt" (lower-case) which you have attached the vlan.10 interface: vlans { MGMT { vlan-id 10;...
View ArticleClik here to view.
Re: Inband Management on EX3300
Corrected but no luck unforunately.I can't ping the interface from the switch itself either. Updated conf:} } me0 { unit 0 { family inet { address 10.255.254.1/17; } } } vlan { unit 10 { family inet {...
View ArticleRe: Inband Management on EX3300
What physical interface/port are you on? You need to add interface into the VLAN, or associated VLAN to interface, Junos allows for both options. If this correct and still not working, then: Does...
View ArticleRe: Inband Management on EX3300
Ok, you cannot reach vlan.10 via me0.0. I expect that you via the management network (10.255.128.0/17) connected to me0.0 has a static route for 10.255.127.230/32 towards 10.255.254.1. Having a /32...
View ArticleJuniper EX4200; Intermittent Packet leak to wrong Routing-Instance VLAN
Hi, We currently have a pair of Juniper EX4200-48T (JunOS 12.3R12.4) running as separate Core LAN Switches, not stacked. They’re both configured essentially the same except for different IP / VRRP...
View ArticleRe: QFX5200: issu yes or no?
Had a pretty bad support experience here. I opened a support case for that asking for this very topic and simply wanted to get an answer - if the datasheet is just wrong or- if the feature will be...
View Article