Re: alarms on ex2200
HI Guys!perfect solution.I will just like to add: In a virtual chassis scenario, make sure you login to affected member and run the commands from their operational mode.Hope it helps!
View ArticleRe: Chassis Alarm Potential slow peers are: spmd When Fusion Configured
Hey, thanks for assisting! It will be much appreciated as it's holding me up from starting to roll this into production. Current case number is 2017-0413-0577, and preceeding case number was...
View ArticleRe: 802.1x broken in Junos 15.1R5.5
Any news?JTAC is still recommending the 15.1R5.5 without mentioning anything about this serious bug.http://www.juniper.net/support/downloads/?p=ex3300#swThat's ugly.
View ArticleRe: EX2300-C private VLANs or port isolation
I agree, the EX2300 is a bit too limited compared to previous platforms. I also find it quite strange to go this way. On comment regarding dot1q and q-in-q. That's not the same :-) dot1q is trunking of...
View ArticleMacsec connection not coming up
The setup I have to realize is:Juniper EX4550 ===Provider Switch===Provider Switch===Juniper EX4550 I was trying to tap the MACsec traffic using an EX4200 with 10G (non-MACsec) uplink module:Juniper...
View ArticleRe: Juniper switch support for the newly approved 802.3bz standard
Unfortunate, our needs are constantly outpacing our vendors, be it Juniper, HP, Cisco, etc. We have need for .3bt enabled switches today, but are currently forced to use a mix of POE+ and POH mid-span...
View ArticleMC-LAG EX9200 To Active/Standby Firewall
Hi, We are planning to buy a new core switch(ex9208) so we have a pair of Core Switch. Right now we have firewall active/standby connect to a core and there's no problem With the current topology(1...
View ArticleRe: Troubleshooting error message
Oddly, I have started getting the exact same message on an interface that has no SFP inserted. Juniper advised it was harmless and to filter the message. This is the only switch I have that does this....
View ArticleRe: MC-LAG EX9200 To Active/Standby Firewall
I believe this is the configuration example you would apply. https://www.juniper.net/techpubs/en_US/release-independent/nce/topics/concept/mf-architecture-network-configuration.html
View ArticleRe: MC-LAG EX9200 To Active/Standby Firewall
Hi Steve, Thanx for the reply, the firewall i use is not juniper, i read the doc u linked, is reth the term use in srx for lacp ? can i just use a standard 802.3ad/lacp in the firewall ? Thx
View ArticleRe: MC-LAG EX9200 To Active/Standby Firewall
Short answer yes, but with MC-AE your attached device MUST be configured and run LACP, as this is required with Juniper MC-LAG implementation. As for A/A and A/S, A/A config on Juniper MC-LAG means the...
View ArticleRe: MC-LAG EX9200 To Active/Standby Firewall
rccpgm wrote:Short answer yes, but with MC-AE your attached device MUST be configured and run LACP, as this is required with Juniper MC-LAG implementation. As for A/A and A/S, A/A config on Juniper...
View ArticleRe: EX2300-C private VLANs or port isolation
Look at a picture of the EX2300-C, and then look at a picture of the SRX300. Made for each other . . . They effectively have the same physical design down to the corner pieces that appear to facilitate...
View ArticleEX switch error message
Can anyone tell me what this message means?/kernel: kuackmem_ackentry_free: Invalid input ackptr 0xd74aafe0, state 0 it happens on multiple EX switches running Junos 12.3R12 but not on switches running...
View ArticleRe: Ex4600 'Error in: SBUS transaction.'
Running across the exact same message myself. Did you ever come up with a fix?
View ArticleRe: Blocking SSH Access EX4500
I know this is extremely old, but it came up when I searched so I figured it's worth answering. The reason the filter doesn't work is that "reject" is not an option with fw filters on EX...if you...
View ArticleRe: Blocking SSH Access EX4500
Firewall Filter should be configured in one of the below fashions. Implicit deny-all case:set firewall family inet filter lpbk term term-1 from <match-1>set firewall family inet filter lpbk term...
View ArticleRe: Ex4600 'Error in: SBUS transaction.'
HI Joel Feb 23 09:57:38 swi-02 fpc1 LBCM-L2,pfe_bcm_l2_mac_add(),702:same mac entryFeb 23 09:57:38 swi-02 fpc1 LBCM-L2,pfe_bcm_l2_mac_add(),690:modid 1 port 0 is_lag_port 1 flags 0x10cc0 trunk_id 1...
View ArticleRe: EX switch error message
HI You can ignore this logs message, this is not impacting. There are internal discssions which has happened on this and have been marked safe logs. 12.1 + dont have this message I think. ThnaksPartha
View ArticleUpgrade EX4200 version 11.4R75 to 15.1R5
Good afternoon, I was looking to see what the upgrade path is from 11.4 to 15.1. I know I will have to get a version of 12 and 14 but trying to minimize how many. Also, I noticed on the site it says,...
View Article