Re: Strange log messages in EX2300
Here is interfaces configuration: interfaces { interface-range ER_0_46 { member-range ge-0/0/0 to ge-0/0/46; unit 0 { family ethernet-switching { interface-mode access; vlan { members VLAN30; } } } }...
View ArticleClik here to view.
Re: Overlapping subnet is configured under irb ERROR
AT PRESENT THE OUTPUT IS- #show interfaces irb unit 1family inet; & WHEN TRIED WITH ASSIGNING IP TO MGMT VLAN (VLAN 1) # set interfaces irb unit 1 family inet address 10.205.35.115/25error:...
View ArticleRe: Setting up a new Virtual Chassis on EX3300
Goes without saying, that the new switches you add to the VC, MUST contain the same image as the current switch.
View ArticleUpgrading JUNOS on 2 EX3300 switches in a Virtual Chassis setup Using J-WEB
Can someone provide me the step by step instructions on how to upgrade the JUNOS on 2 EX3300 switches in a Virtual Chassis setup using J-WEB. If it is not possible using J-WEB, can someone please...
View ArticleEX4500 Dropped Packets
We were running Junos 12.3 R11.2 on our EX4500 Core, an EX4500 in our DR site, and all of our EX4200 edge switchesWe upgraded all of them to Junos 15.1 R5We use Veeam for backup and replication and two...
View ArticleRe: Tail-dropped packets on 30Gb AE while only ~8Gbps at max
Did you ever figure out the cause of thisWe upgraded our EX4500 from Junos 12.3 to 15.1 and during our backup and replication jobs we are seeing a lot of dropped packets
View ArticleRe: EX4500 Dropped Packets
I did find that there a lot of open PRs for dropped packets under Junos 1.51...
View ArticleRe: EX4500 Dropped Packets
We do not. The EX4500 at our core does all the routing for our vlans with 26 RVI. All the other switches are layer 2 only
View ArticleRe: EX4500 Dropped Packets
Have you check the Transmition? is it a patchcord or DWDM ? In my case I have that problems with that chassis and the origin was the CPU (sfid process) and the reason was that the SNMP. I block all...
View ArticleRe: EX4500 Dropped Packets
There is a Veeam replication going on right nowEX4500 core switch has 67% idle, 14% sfidEX4500 DR switch has 94% idle, 1% sfid
View ArticleRe: EX2200 system overload problems with 15.1Rx upgrades
12.3R12 Recommended Release for EX2200 and EX2200-Chttps://kb.juniper.net/InfoCenter/index?page=content&id=tsb17138&actp=METADATA
View ArticleRe: 2 members Virtual chassis traffic handling
Hi Spuluka, Thanks for your information. I 've followed your recommendation to add the new commands to the virtual chassis. But it still not works. Do you have any suggestions? Attached detail log for...
View ArticleNew to JunOS configuration
I have an EX3300 stack in my core MDF closet and various model Cisco stacks in the edge closets.I need to configure a VLAN and associated ports on the EX3300 stack and I'm very familiar with the JunoOS...
View ArticleRe: Upgrading JUNOS on 2 EX3300 switches in a Virtual Chassis setup Using J-WEB
Try the links below: http://www.juniper.net/documentation/en_US/junos12.3/topics/task/installation/virtual-chassis-ex4200-ex4500-software-cli.html...
View ArticleRe: 2 members Virtual chassis traffic handling
>show virtual-chassis status>show virtual-chassis vc-port statistics>show virtual-chassis vc-path>show virtual-chassis>show chassis pic-modeIf the PIC mode setting is not set to...
View ArticleRe: Overlapping subnet is configured under irb ERROR
This subnet 10.205.35.115/25 overlaps with another interface on the device. You can use this to find the interface. #show | display set | match 10.205.35. You can then either change the interface so...
View ArticleRe: 2 members Virtual chassis traffic handling
In addition to the VC status commands that Lyndidon lists, can you also run show interfaces terse So we can confirm the interfaces are recognized.And alsoshow chassis hardware models Finally, when you...
View Article