Re: EX4600 Virtual Chassis - having trouble making it show up.
In a mixed Virtual Chassis of EX4600 and EX4300 switches, the Junos OS release dictates whether the EX4600 is best used in the master role. For Junos OS releases between 13.2X50-D10 and 14.1X53-D25,...
View ArticleRe: EX4600 Virtual Chassis - having trouble making it show up.
Does show chassis hardware actually show the QSFP DAC? For example: PIC 0 BUILTIN BUILTIN 24x 40G-QSFP Xcvr 0 REV 01 740-038623 XAN16EC18719 QSFP+-40G-CU1M
View ArticleRe: EX4600 Virtual Chassis - having trouble making it show up.
First 4600root> show chassis hardware Hardware inventory: Item Version Part number Serial number Description Chassis TC3715500010 EX4600-40F Pseudo CB 0 Routing Engine 0 BUILTIN BUILTIN EX4600-40F...
View ArticleRe: EX4600 Virtual Chassis - having trouble making it show up.
I resolved the problem, I was setting the wrong port for the pic-slot. Once I set to port 24 and 25, all came up. root> show virtual-chassis vc-port fpc0:...
View ArticleRe: EX4600 Virtual Chassis - having trouble making it show up.
Oops. Glad it was an easy fix.
View ArticleRe: LAG with active/passive links
Johnathan, That solution would not work, because both physical links of the same LAG/Etherchannel should terminate on the same switch. You can't "split" it between the two different switches. The best...
View ArticleRe: Which JunOS version should I install on EX2200/3300/4500?
The JTAC recommended release article is prepared by the support team at Juniper. They recommend releases by platform based on their experience with call volume and reported critical issues. As a...
View ArticleRe: How to troubleshoop flapping ports?
You can create a group that applies the no-trap to every interface. set groups MYGROUP interfaces <*-*> no-trapsset apply-groups MYGROUP Then override this with traps on the desired interfaces...
View ArticleMoving "vlan mapping" config. from Cisco 3750 switch to Juniper EX4200 VC
Hello,I'm need your help, few days I tried move "vlan mapping" configuration from Cisco 3750 to Juniper VC EX4200 and at the moment not successfully, I have following coniguration on Cisco 3750:...
View Articleex2200 usb needed for boot
Hello. I have an ex2200-24p-4g poe. I am having an issue where the only way i can get the device to boot is if i have both the power lead and the usb plugged into a computer. If i pull either of these...
View ArticleRe: EX2200 15.1R1.8 adding VLAN to interface is not accepted - is it the...
my mistake, VLAN Name was removed and added by its VLAN ID all good
View ArticleAllow guest to acess employee resource
Hello,There are two vlans (employee and wifiguest), Firewall filters separate traffic on ex4200.I would like to allow wifiguest to access a specific IP address on the employee vlan and no other...
View ArticleEX4600 command different for ether-options then in EX4200 how to do it.?
In my EX4200 I have the following command set interfaces ge-2/0/36 ether-options 10m This will not work int he EX4600, what can I do to set speed this way.? admin@DSOSW01# set interfaces ge-2/0/36...
View ArticleRe: Disable Virtual Chasis on EX4200
Thanks this thread has helped me remove a switch form the VC, Sadly in learning how to disable and remove the VC I have decided to redesign my office uses VCs to reduce device maintanance - LOL
View ArticleRe: ex2200 usb needed for boot
This is not normal behavior. You should open a JTAC ticket. You will likely need to RMA the switch.
View ArticleRe: EX4600 command different for ether-options then in EX4200 how to do it.?
Looks like the ex4600 uses the QFX layer two commands. http://www.juniper.net/documentation/en_US/junos14.1/topics/task/configuration/ten-gigabit-interfaces-qfx-series-cli.html And the bad news is:...
View ArticleRe: EX4600 command different for ether-options then in EX4200 how to do it.?
Yes, EX4600, QFX product line, EX4300, EX9200, any newer switches all use ELS CLI format. This is covered here:...
View ArticleRe: EX4600 command different for ether-options then in EX4200 how to do it.?
Well, the problem with using auto-neg for 10/100 links is that there is no real standard and they frequently do not correctlynegotiate a good link in a cross vendor application. I've never had a...
View ArticleRe: Allow guest to acess employee resource
Assuming your guest wifi is 10.2.2.0/24 and the specific address is 10.1.1.100/24 set interfaces vlan unit 999 description "guest wifi" set interfaces vlan unit 999 family inet filter input...
View Article