Why is 802.1X on trunk ports not supported?
So a bunch of security critical VLANs terminate at our WLAN access points (the APs themselves are 802.1X enabled in regard to wireless clients). Hence, all an attacker needs to do is unplug an AP, plug...
View ArticleRe: Why is 802.1X on trunk ports not supported?
Question: Are you saying that on Cisco switch that if you enable 802.1x on your trunk interface and then attach the AP to it (with the AP also supporting 802.1x) that everything then works properly?
View ArticleRe: Why is 802.1X on trunk ports not supported?
Yes, that's exactly what I'm saying. The AP is connected to a switch, with the uplink being configured as a trunk port. The VLANs which terminate at the AP are statically assigned on the uplink port of...
View ArticleRe: Why is 802.1X on trunk ports not supported?
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/dot1x.html Release 12.2(33)SXJ and later releases support the Network Edge Access Topology (NEAT)...
View ArticleRe: Allow guest to acess employee resource
smicker - thank you, I will give this a try.
View ArticleRe: Trunks, Vlan members all - and Native Vlan ID
I might be 4 years late, but yes, I 'm surprised. It almost cost me a customer some months ago, I was lucky to have found what the cause of my native vlan not working was in time. Plus, I have found...
View ArticleClik here to view.
Ex4600 VC - routing problem and interface not available.
Thanks for helping on this.First I have a routing issue, that should not be, but believe the interface not available is the bigger problem. {master:0} admin@DSOSW01> show interfaces ge-3/0/42...
View ArticleHow to monitor Logical Interface flags
Hi, My platfrom is vcf mixed mode with qfx5100 and Ex4300 I configured storm-control with "action-shutdown" i noticed that when the strom-control pass the thresholdThe logical interface flage change to...
View ArticleRe: Ex4600 VC - routing problem and interface not available.
Yes, your 4600's are fpc 0 and 3, the 4300's are fpc 1 and 2. Preprovision your VC if you have any static port role requirements.
View ArticleRe: Ex4600 VC - routing problem and interface not available.
micker, thanks,Does this make sense.? fpc0: = 0/0/0fpc1: = 1/0/0fpc2: = 2/0/0fpc3: = 3/0/0 well I believe I found my routing issue. The l3-interface valuses did not copy over. Will add them...
View Articledot1x itself disconected
HII have EX4200 and configured dot1x. Authentificate works normal, but some devices (on some ports) itself disconnect.In logs have follow messageMar 23 14:44:41 2016 jun-test dot1xd[66489]:...
View ArticleOnly IRB interface is supported
Having aproblem recreating the vlans on a EX4600/4300 VC. In my previous config the following was the code for the vlans; set vlans DMZ vlan-id 5 set vlans DMZ l3-interface vlan.5 set vlans DMZ-8...
View ArticleRe: Only IRB interface is supported
The best place to start is here: http://www.juniper.net/documentation/en_US/junos15.1/topics/task/configuration/getting-started-els.html All the new Juniper switching products, EX4300, EX4600, QFX5000...
View Articledot1x to long reconnect
HiI have EX4200. All the necessary settings for work dotx are made.When i first time plugged to dot1x port any devices authentication occurs fast. When i do administrative down that dot1x interface a...
View ArticleMassive rolling VOIP issue please help (ex3300 stacks)
Hello, We recently upgraded from old Cisco/avaya switches in our closets to stacked ex3300's to a new Nexus (A/B) core Setup:The uplinks are 10G with 2 uplinks (one to core one to core b) per stack in...
View ArticleCannot add static ip on Ex 3300 which is configured with DHCP
Hello, I have EX 3300 POE switch on which DHCP is configured , I cannot connect a machine in static IP to the ports in the switch, I heard about port secuirty and other issue can some one help me to...
View ArticleRe: dot1x to long reconnect
Hi, I'm not sure if this one is related to this PR1127566 To make sure, try this workaround:Enable dot1x feature without using "set protocol dot1x interface all". This should ensure dot1x to operate...
View ArticleRe: dot1x to long reconnect
Thank you for this problem report. It is very similar. But i no used configuration command "protocols dot1x authenticator interface all" and core dump file is clear. My configuration belowinterfaces...
View ArticleRe: Cannot add static ip on Ex 3300 which is configured with DHCP
Sorry for stupid question, but what means "I cannot connect a machine in static IP to the ports in the switch"? Port no activared or you can not ping mashine with statis ip or in something another? Do...
View ArticleRe: Massive rolling VOIP issue please help (ex3300 stacks)
As a test, what I would suggest is statically assigning a port to be in the voice VLAN on the switch, and then try putting a laptop first with a static IP on it (in the correct subnet obviously), then...
View Article