Re: Is it just me or is support getting useless ?
Actually EX4200 which yeah I know is end of life next June. Switch s/n is in system but power supply s/n not in their system so I sent a photo of it. In the past they added, this time they said since...
View ArticleRe: Is it just me or is support getting useless ?
Hi Folks,I would suggest to Escalate the JTAC Cases under such conditions, If for any reason you are not satisfied with the progress of your case, you can escalate the case at any time. Escalating a...
View ArticleRe: Is it just me or is support getting useless ?
To add… You can also escalate a Case to a JTAC Escalation Manager Over the Phone. Please call any of the JTAC phone numbers and select Option #2 to reach Customer Care. Once you reach Customer Care,...
View ArticleRe: QFX to EX lacp not working
Yet the mystery will remain unsolved; Good to hear things are working now as expected…
View ArticleRe: How can I clear RSTP topology changes counter
Hi Folks,I do find ‘clear spanning-tree statistics’ is the only option available with ex3300 and this may not clear the topology, {master:0}root@ex3300> clear spanning-tree ?clear spanning-tree...
View ArticleMAG6611
My company purcahesd MAG6611 and ask me to configure it, i am working well with Juniper SRX Series but i have no idea how to start emplement MAG6611, can any body guide me how to start emplement it...
View ArticleRe: MAG6611
Juniper sold this product line to a private equity firm and it is now marketed under the Pulse Secure name. They have user forums over here....
View ArticleRe: MAG6611
Thanks for reply i need to operate both mode in one device is it possible, do you have any Documentation which can help me?
View ArticleRe: MAG6611
It is not possible to run in both modes. There is a different software load that goes onto the appliance depending on which mode you are using. And the two are separately licensed for the number of...
View ArticleRe: MAG6611
Hi Folks,My 2 cents on this… MAG Junos Pulse Gateway Unboxing & Quick Setuphttps://www.youtube.com/watch?v=nF-1KPk_ZoU Juniper SSL VPN Tutorial and Demo - Setup resources, users, sign in...
View ArticleRe: interfaces don not come up
Below are the steps, I would recommend for troubleshooting: 1. Make sure the correct fiber cables are being used between the two segments (MM or SM), 2. Make sure to test the fiber the link running...
View ArticleRe: SFP not showing up in config EX4500
Hi Folks,Just want to check if it is Juniper SPF or other vendor SFP?
View ArticleEX4550 VC questions
Hi all, I'm installing an 2x 32GE Virtual Chassis Module into my EX4550. This is what I see when the module is installed: {master:0} root> show virtual-chassis vc-port fpc0:...
View ArticleRe: SFP not showing up in config EX4500
Hi, The SFP in questions is a Copper SFP or a fiber SFP ? Was there any negotiation problem?
View ArticleRe: Is it just me or is support getting useless ?
I'll try escalation next time although I'm not too hopeful. The gear isn't end of life yet but sure seems like they want it to be and it's like talking to a brick wall getting anything out of them....
View ArticleDHCP Single Fixed Address per Port
Greetings, I'm trying to figure out how to setup networking for an array of industrial devices. There are 100 of these devices, each identical. My hope is that I can have these devices automatically...
View ArticleRe: DHCP Single Fixed Address per Port
I ran into a similar requirement and found no straight-forward feature or set of functions to achieve it in Junos. I considered a couple approaches and ultimately went with a brute-force, bulky...
View Article