MX and AE loadbalacing
So after doing a lab test between a Ex and QFX using a traffic genarator we noted that traffic flow went over one member interface and returned over the other. We did the same test but the result looks...
View ArticleRe: MX and AE loadbalacing
Hi, On MX, can you try configuring load-balancing per-packet configuration? It says per-packet, but it really is per-flow load-balancing in implementation. [edit routing-options forwarding-table]export...
View ArticleRe: MX and AE loadbalacing
As @pranavs stated, what occurs in Juniper products, and most all other products is based on flows, not packets. Plus, no one really does load-balancing, it is really load-sharing. Based upon...
View ArticleRe: QFX3500-48s4q-acrb stuck in virtual chassis/linecard config
Did you try to 1) delete the whole config but the root password 2) apply your own preprovisioned VC configuration with this single switch defined as member ID 0 and routing-engine role (you will have...
View ArticleRe: MX and AE loadbalacing
Thansk for your replies really appriciate. However i think i didnt post my question in the right context. I understand the loadbalacing mechanism per AE from a single device point of view. My question...
View ArticleRe: MX and AE loadbalacing
See attached what i am trying to achieve. I will be deploying a cache solution, but instead of using the more complex and cumbersome PBR with firewall filter etc. i want do add the devices in the...
View ArticleRe: SRX Switching vs. Cisco
@SpulukaNO, intravlan traffic which is locally switched in my opinion does not really affect the Performance numbers given in IMIX or large packets, or....So it needs NOT to be included in the...
View ArticleCisco to Juniper switch p2p connectivity with failover
Hi, We have Cisco 6506 switch at H.O. and Juniper Ex switches (4300, 4200) at branch location. We are planning to connect both office with 2 point to point link. If one link goes down second link will...
View ArticleRe: Cisco to Juniper switch p2p connectivity with failover
Hello,Easiest way would be to use either1/ Flex Link on CSCO side https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3550/software/release/12-2_25_see/configuration/guide/swflink.htmlor2/...
View ArticleRe: Cisco to Juniper switch p2p connectivity with failover
Hi,What will be p2p link type. Layer2 or layer3.
View ArticleRe: Error while upgrading.
Fo SRX1400 ISSU cluster upgrade I am getting below error:Any suggestion to resolve the issue? root@SDBRONRS04W> ...unos-srx1k3k-12.3X48-D50.6-domestic.tgz Checking compatibility with...
View ArticleRe: SRX Switching vs. Cisco
Intra vlan is the traffic between the same vlan/subnet. This should be linerate speed because I have created switch/L2 ports and for this scenario the SRX acts as a regular switch (it doesn’t apply any...
View ArticleEX4200 high rpd process allocation with rsvp and mpls
Hello readers,When rsvp and mpls are added to port configuration rpd process allocate much more memory then expexted and in time it would use all remaining memory and freeze the box. Without rsvp and...
View ArticleClik here to view.
Re: Cisco to Juniper switch p2p connectivity with failover
Hello,I see You haven't actually read the links I supplied. No probs, it happens all the time CSCO saysFlex Links are a pair of a Layer 2 interfaces (switch ports or port channels) Same for Juniper....
View ArticleRe: SRX Switching vs. Cisco
I didn't believe that security flow would not apply on SRX ports in ethernet mode so I ran that same test in my own lab and was surprised to see you cannot apply security policies to switched traffic...
View ArticleRe: Overlapping subnet is configured under irb ERROR
I was running into this same (or very similar) problem with an ex3300 runing Junos 15.1R6-S2.1. It is a l2 switch with a management vlan (the only interface with family inet is vlan.100). vlan.100 is...
View ArticleRe: Unknown error
I just ran into this problem, and wrote up a way to work around it (without having to remove the l3-interface, reboot, and re-add the interface to change the netmask) in this thread:...
View ArticleClik here to view.
EX3300 IP SLA
Hi guys, I need help with a certian configuration setup I'm having trouble with. Here is my physical setup: I have 3 switches - Switch-A, Switch-B and Switch-C.Switch-A is the user switch and...
View ArticleRe: EX3300 IP SLA
Yes, I know.Does RPM need a special license? Will RPM help me in this specific scenario? Could you provide configuration examples?
View Article