Re: EX3300 IP SLA
Thanks Karan, I'll check those links.Is there any other option to successfully get what I need without using any special methods and just configuring 2 simple static routes?
View ArticleRe: EX3300 IP SLA
Unfortunely no (AFAIK for sure), those rpm probes are must to automate the failure detection.
View ArticleRe: 12.3R12-S8 TSB
Hi, JUNOS 12.3R12-S8 was released just a couple of days ago (31st JAN 2018) & JUNOS 12.3R12-S8 TSB is yet to be published.
View ArticleRe: Cisco to Juniper switch p2p connectivity using 2 different ISP...
Hi Alex,Thank you and appreciate your efforts..The scenario is P2P solution in between Cisco 6506 switch(H.O.) and Juniper EX 3400/4300(Branch location) for max 60 users.Two Layer3 Link(different ISP)...
View ArticleRe: Cisco to Juniper switch p2p connectivity using 2 different ISP...
Hi, Following is my understanding about your scenario. Since provider link is an l3 link.your topology will be as follows. Cisco 6509 (stand alone or VSS) --->192.168.1.0/30(provider/Cisco...
View ArticleRe: Cisco to Juniper switch p2p connectivity using 2 different ISP...
Hi Milind, We have standalone cisco 6506 switch and 2 Layer 3 p2p link. Both link need to up and pass network traffic. We have concern about MPLS and IPsec functionality on EX platform. Thank you
View ArticleRe: Cisco to Juniper switch p2p connectivity using 2 different ISP...
As you yourself already stated, EX4300 does not support IPSEC or MPLS (L3 VPN I assume is what you would be looking for?). 2milindmistry already told you solution was to run some Routing protocol, like...
View ArticleRe: Cisco to Juniper switch p2p connectivity using 2 different ISP...
Hi Nikhil,I think solution is to use dynamic routing protocol with ecmp as i mentioned above.MPLS is not supported on Ex 4x00 series switches.IPsec over ospfv3 is supported only on ex series.pl note...
View ArticleRe: 12.3R12-S8 TSB
12.3R12-S8 fixes some bugs in J-Web interfacehttps://kb.juniper.net/InfoCenter/index?page=content&id=JSA10828&pmv=print&actp=RSS&searchid=&type=currentpaging
View ArticleRe: 12.3R12-S8 TSB
C-3PO, The list if bug fix for Junos 12.3R12-S8 in TSB is yet to be pubished. (it will be out soon).There are total of 13 PR/Bug fixes in Junos 12.3R12-S8 & the JSA you listed is one of the bug fix...
View ArticleJunos 12.3R12-S7 for EX2200 breakes VC LACP MC-LAG
We have ex2200-48p-4g 4-member VC. show virtual-chassis Preprovisioned Virtual Chassis Virtual Chassis ID: 53c4.a597.02bb Virtual Chassis Mode: Enabled Mstr Mixed Route Neighbor List Member ID Status...
View ArticleJuniper QFX5110 and Catalyst 3560 problem
Hi guys, So I faced a really weird problem. I have a QFX5110 switches bundled into Virtual Chassis. And I have a standalone Cisco Catalyst 3560 switch. I'm trying to setup a simple trunk between them...
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
BTW in log messages I can see Feb 5 11:21:03 cvc kernel: if_msg_ifd_add: l2_count in add (0), for ifd:ge-0/0/26 Feb 5 11:21:03 cvc kernel: if_msg_ifd_add: l2_count in add (0), for ifd:ge-0/0/26 Feb 5...
View ArticleRe: QFX igmp-snooping not working
it's working now. My mistake was using the same vlan for the source and my private network. So now, I use 2 vlan, one for the source (only one port) and one for my private network (about 10 ports)....
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
Since this is emptyI tried to do command show interfaces diagnostics optics ge-0/0/26But it doesn't even get me any output ! I suspect an issue with the optic. Can you see if the optic shows up as...
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
Coupl of tests u may perform as follows...1. physicially loop the ethernet cable between two ports of qfx 5110..2. if the ports came up, then do similar exercise with cisco (i believe u seem to have...
View ArticleCannot delete an interface, why?
I have an EX4500 with an interface with nothing plugged into it. I go into J-web, delete out this section, and click commit xe-0/0/1 { description "vSphere15 Management"; mtu 9216; unit 0 {...
View ArticleRe: Cannot delete an interface, why?
Seems that you have configured the xe-0/0/1 in rstp or vstp..Since xstp is not able to find the interface post deleting, you seem to be encountering the mentioned error..you may delete the interface...
View Article