Re: EX4300 Firewall Filters and Hosting Vlans
I will give it a try later this week. I appreciate the assitance.
View ArticleEx4300 version 14.1X53-D45.3 high cpu when dhcp-snoop is configured
Hello,My setup is Ex4300 13.2X51-D30.4 (vc with 3 members), another Ex4300 13.2X51-D30.4 (vc with 3 members ), every one of them Is connected to Ex4600 14.1X53-D30.3 (star topology), on all switch i...
View ArticleRe: MST Reqion 0 VLAN Exemption
Thanks for the reply, also if the VLAN isn't configured on the switch that MSTI instance is sort of orphaned...it makes a bit of a cluttered MSTI config, but it works.
View ArticleRe: Determining utilization of the forwarding table on a QFX3500
show chassis fpc <x> will give you Memory an CPU util of the line card. Do not forget kudos if it helped. Thanks,
View ArticleRe: HTTPS not working on EX4600
I was able to get HTTPS working, although to be honest I'm not sure what did it. I opened a case with TAC and tried additional suggestions such as creating a local cert, regenerating the system...
View ArticleRe: HTTPS not working on EX4600
Glad you have it working and thanks for the update. Agree it does feel like some kind of bug in the version originally loaded.
View ArticledotX, dynamic vlan plus LLDP-MED
Hello Community, we face an issue and do not know where we are going wrong. We general started with this setup guid:...
View ArticleRe: dotX, dynamic vlan plus LLDP-MED
Have you looked here - https://www.juniper.net/documentation/en_US/junos/topics/example/802-1x-pnac-single-supplicant-multiple-supplicant-configuring.html For this configuration...
View ArticlePreventing BPDUs being sent on STP active port
I haven't been able to find an obvious way to prevent a port running STP from sending out BPDUs. I'm specifically working with VSTP and the ELS sortware. I can put a port into 'edge' mode, which I...
View ArticleEX3300 uplink ports
Hi,Sorry if my question is dumb, but I was not able to find the right answer by myself.On EX series (especially 3300), is it possible to use uplink ports as "regular" ports, in order to get four added...
View ArticleRe: EX3300 uplink ports
Hi Yes, you can use those uplink ports as regular network ports. Note: out of box, 2 out of 4 (last 2 uplink port) are configured as VC ports by default. you can either configure all of them as VC or...
View ArticleRe: dotX, dynamic vlan plus LLDP-MED
at current we have Multi-Sublicant but still stuck. Does this requier that the phone also send 802.1x Auth or will LLDP-MED pass the vlan and grand access based on LLDP message? I can assume due to...
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
OK so I started fresh on new Cisco port Gi0/51 Here is the results On Cisco side the port is configured in such a wayinterface GigabitEthernet0/51 switchport trunk encapsulation dot1q switchport mode...
View ArticleHelp me troubleshoot my network.
Hi Guys, I have a bunch of IIS servers connected to a QFX5100 VC via 10Gig DACs. The QFX5100s are connected to an SRX 550 active/passive HA cluster. There is a VPN tunnel that goes to another...
View ArticleEX4200: chassisd PoE status - explanation
Hi experts, can someone pls. sheed a light on the following log messages:chassisd[1298]: PoE port name ge-0/0/2 status 1chassisd[1298]: PoE port name ge-0/0/2 status 27chassisd[1298]: PoE port name...
View ArticleRe: EX4200: chassisd PoE status - explanation
Hi,The status 27 indicates OFF and 1 indicates ON.These messages are informational & they are related to the status of the PoE on the interfaces.Do you you still these messages?
View ArticleRe: EX4200: chassisd PoE status - explanation
Hi, We see this (and similar) messages from time to time.As we have a large WiFi infrastructure, the PoE state would help us with troubleshooting the state of the APs.Is there a complete list of states...
View ArticleRe: EX4200: chassisd PoE status - explanation
37 is when port isn't opterational. chassisd status is for jtac debug info and you get these messages if port flaps.Generally you should verify the port state/status with: -> show poe...
View ArticleEnable SSH to interface EX2200
My one goal is to be able to plug an RJ45 to this switch, manually set my IP, and SSH to the device. That being said, this is my first junOS device, and I'm simply learning on it. I just purchased an...
View ArticleRe: Enable SSH to interface EX2200
Hi, You need to assign IP address to your laptop as well say 192.168.1.6/24 and gateway as 192.168.1.5. Please try to ssh once you configure the IP on laptop. Regards,Rahul
View Article