Re: Cannot delete an interface, why?
That was it, once I removed it from the RSTP section, I deleted the interfaceThanks
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
Optics is visible.FPC slot 0, PIC slot 0 information: Type 48x10G-4x100G State Online PIC version 3.24 Uptime 84 days, 6 hours, 42 minutes, 32 seconds PIC port information: Fiber Xcvr vendor Wave- Xcvr...
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
Also this is output of show interfaces ge-0/0/26 Physical interface: ge-0/0/26, Enabled, Physical link is Down Interface index: 764, SNMP ifIndex: 799 Link-level type: Ethernet, MTU: 1514, LAN-PHY...
View Articlevirtual switch with preprovisioned conf: promote line cards to routing engine...
Hello community,I have a VC with x2 4200 (member 0 & 1) and x2 4550 (member 2 & 3).In preparation for upgrading the x2 4200 to 4550, I want to promote member 2 and 3 to routing-engine and...
View ArticleMST Reqion 0 VLAN Exemption
I'm presuming no, but I was wondering if there was a way to configure MST such that there were VLANs, while not mapped to any instance, ALSO were not mapped to instance 0 (the CST instance). Basically...
View ArticleHow to integrate Huawei s57200 and juniper ex2200
Dear All, Please help to solve dhcp problem.Please see the my network diagram.i connect to juniper switches to huawei s5720.I configure dhcp server for all vlan in s5700.i have 3 vlan .VLAN10 for CCTV...
View ArticleRe: Juniper QFX5110 and Catalyst 3560 problem
Did you physically loop the cables as i mentioned? It will tell you if there is anything wrong with cables, optics (sfps) or port..
View ArticleRe: virtual switch with preprovisioned conf: promote line cards to routing...
I think both of your options are valid and can do the job. However, for option 1, when you are switching config from non provisioned chassis to pre-provisioned chassis along with role changes, VCCPD...
View ArticleRe: How to integrate Huawei s57200 and juniper ex2200
Hi, Is Huawei s57200 the DHCP Server? If yes, Configure the EX2200 to be DHCP Relay/Bootphttps://kb.juniper.net/InfoCenter/index?page=content&id=KB13206&actp=METADATA
View ArticleRe: virtual switch with preprovisioned conf: promote line cards to routing...
I tested it (option 2) and worked like charm. It takes a couple of minutes from the moment you applied the configuration until the roles are updated so don't panic.Thanks a lot for the advice. Jaime
View ArticleEX4300 Firewall Filters and Hosting Vlans
I am currently in a spot where I am trying to figure out the configuration of an EX4300 for my network. I am not sure how to setup the firewall filters to permit the correct traffic to pass in/out of...
View ArticleRe: EX4300 Firewall Filters and Hosting Vlans
Hi There,Here are some pointers in setting up the switch: Includes basics set of configuration...
View ArticleHTTPS not working on EX4600
I have a EX4600 that I am setting up. I have also configured HTTP and it works just fine. When I attempt to connect via HTTPS the browser simply does not connect to JWEB page, just the generic "site...
View ArticleRe: HTTPS not working on EX4600
My 2 cents:Could you delete HTTP and enable only HTTPS and check?
View ArticleRe: HTTPS not working on EX4600
Removed http, restarted web managemenent service, and the issue persisted. I have connected my management machine directly to the management port on the EX4600 and still the issue persists, cant...
View ArticleRe: HTTPS not working on EX4600
Would you be able to enable web management http and try following prcedure?https://kb.juniper.net/InfoCenter/index?page=content&id=KB19595Also, do you get anything in syslog while accessing the...
View ArticleRe: HTTPS not working on EX4600
Could you please tell us what version of code you are using? This is always helpful information for these situations? Do you have a TAC case open as well? Thanks
View ArticleRe: HTTPS not working on EX4600
I remember having to do this manual cert creation on some ex switches a while ago. Perhaps the system generate is not working on your...
View ArticleRe: MST Reqion 0 VLAN Exemption
If you simply do NOT include any of the interfaces in the vlan you want to include in the mstp protocol then the vlan will NOT participate in MSTP. Only interfaces configure here do.protocols mstp
View ArticleRe: HTTPS not working on EX4600
I do know someone who has this working with EX4600, so it is very likely something to do with your specific setup. FYI Only.
View Article