Re: Enable SSH to interface EX2200
On laptop did (plugged into ge-0/0/2): ifconfig eth0 192.168.1.6 netmask 255.255.255.0 route add default gateway 192.168.1.5I thought, and this may be the base of my confusion, when you set the inet...
View ArticleRe: Enable SSH to interface EX2200
When you set the ip address on the ME port you must connect to the ME port. This interface is isolated from the main revenue ports so you cannot reach it from any other path. When ip addresses are...
View ArticleVRRP over IRB - can't ping L3 interfaces
Hi AllA quick question please, perhaps I'm missing somehing.I have a pair of QFX10K, they're connected with 2x100G in LACP Lag.Both are connected to a firewall cluster, and the irb interface servs as...
View ArticleRe: VRRP over IRB - can't ping L3 interfaces
Did you tried the method mentioned in the below KB? https://kb.juniper.net/InfoCenter/index?page=content&id=KB27865 Regards,Rahul
View ArticleRe: VRRP over IRB - can't ping L3 interfaces
Hi RahulThanks for your reply.The current configuration between the 2 interfaces is MC-LAG, there's an ICL-PL Link between them which is a trunk contains all vlan members should be transit under the...
View ArticleClik here to view.
Re: VRRP over IRB - can't ping L3 interfaces
Hi, You can read the below document. https://www.juniper.net/documentation/en_US/junos/information-products/pathway-pages/mc-lag/multichassis-link-aggregation-groups.html Routing protocols run on the...
View ArticleRe: VRRP over IRB - can't ping L3 interfaces
labroot@TEST# show interfaces ae29 | display inheritance no-comments mtu 9100;aggregated-ether-options { lacp { active; periodic fast; system-id 00:29:29:29:29:29;...
View ArticleRe: VRRP over IRB - can't ping L3 interfaces
As you discovered, yes for this to work you must map IP to MAC via the l2-interface knob. Just as a point of reference, if you use Network Director and it's MC-LAG functionality, ND will automatically...
View ArticlePermissions to only activate and deactivate dhcp-server
Hi Experts,I am struggeling with exact user permissions. A User should be able to issue the following 2 Commands (via op script):deactivate system services dhcp-local-serveractivate system services...
View ArticleQFX Virtual Chassis Routing engine switchover considerations
Hi we have a production qfx virtual chassis (ring topology) built up by 5 qfx 5100 members (x2 RE & x2 LC). There's no Routing engine priority set on the configuration and FPC 1 (memeber1) is actig...
View ArticleRe: VRRP over IRB - can't ping L3 interfaces
Hi rnayar, Thanks a lot for your detailed answer and explaination, I appriciate the time you took to answer this and your outputs your shared.Extraordinary! David
View ArticleEX3300 LLDP-MED and ShoreTel 400 series phone - works intermittently
I'm not sure if this is a problem with ShoreTel (now Mitel) phones or a problem on my Juniper switch. I have a 24 port EX3300 on Junos: 15.1R6.7. and LLDP-MED only works intermittently. What I mean by...
View ArticleRe: QFX Virtual Chassis Routing engine switchover considerations
Are you taking about below KB? https://kb.juniper.net/InfoCenter/index?page=content&id=KB29511 Regards,Rahul
View ArticleRe: MCLAG Question
I guess below link helps. https://www.juniper.net/documentation/en_US/junos/information-products/pathway-pages/mc-lag/multichassis-link-aggregation-groups.html Regards,Rahul
View ArticleRadius & routing-instance
Hi, Does anyone have a working configuration with Radius and routing-instances?I have tried to use a lo0 interface instead of vlan interface that is in the routing-instance and have that as source for...
View ArticleRe: Radius & routing-instance
Do you have reachabilty from Routing-Instance to Radius Server?
View ArticleRe: Radius & routing-instance
Hi Karand!Yes I do set system radius-server 10.7.163.16 source-address 192.168.117.1ping 10.7.163.16 routing-instance ABCPING 10.7.163.16 (10.7.163.16): 56 data bytes64 bytes from 10.7.163.16:...
View ArticleRe: Radius & routing-instance
In MX, we have option to call the access-profile in routing-instance, but in EX, the options are limited. Have you tried to call the routing-instance in access? labroot@EX42SW# show | compare[edit]+...
View ArticleRe: Radius & routing-instance
Hi, Yes I have tried it and I get this log Feb 20 10:23:09 SW1 sshd[285]: sendmsg to 10.7.163.16(10.7.163.16).1812: h->try:0 serv->num_tries:0, serv->max_tries:3 tries_per_addr:3, nleft:3,...
View ArticleRe: Radius & routing-instance
Can you verify reachability from the assigned source address. set system radius-server 10.7.163.16 source-address 192.168.117.1ping 10.7.163.16 source 192.168.117.1
View Article