Re: EX4300 / PulseSecure Gateway Internal Port Native VLAN
Reviewing the documentation then your configuration is correct. The appliance will have a untagged address in vlan 25 and that is what you will configure on the port on the ex as well.
View ArticleRe: Assign IP for each me0 interface on switch in a VC
Thanks for the reply, took a look and that article applies to MX series routers/EX9200. Doesn't apply to my situation.
View ArticleDaisy chain IP phone and printer, will it work?
We are a K-12 school district and nearly every classroom has a networked laser printer. We will be putting in IP phones over the next six months. The IP phones all have two RJ45 jacks, and in and an...
View ArticleRe: Daisy chain IP phone and printer, will it work?
I did a little research and it appears there might be two methods to do thisTag one type of traffic (IP phone or printer) and do not tag the other type of trafficUse LLDP-MED to have the switch...
View ArticleRe: Daisy chain IP phone and printer, will it work?
This type of setup could work, but it requires the correct configuration on the switch port where the phone is connected and the phones to also support the basic protocols. Typically this would have...
View ArticleRe: Assign IP for each me0 interface on switch in a VC
No, when you create the virtual chassis they are managed as a single device. You can connect all the console and me ports but they will redirect to the currently active RE role switch.
View ArticleRe: EX4300 / PulseSecure Gateway Internal Port Native VLAN
Hi,thanks for your feedback.In the meantime, we were able to setup a LAB and tested this out.It works well. Just one modification was needed: the native vlan was only in the native-vlan-statement and...
View ArticleClik here to view.
Add new Interfaces to MSTP-Config during runtime
Hi all, just a quick and really simple one :-)please confirm: after adding new ports to the switch-config, I also want to include these new ports within the STP-Config (MSTP).The new ports will be...
View ArticleMSTP ELS Switch vs NON-ELS
Hi,just two short questions:1)On an EX4300 with ELS-Firmeware, when I configure MSTP, I only can select the "whole" interfaceset protocols mstp interface ge-0/0/27When I configure MSTP on a...
View ArticleMultiple VLAN Rename in one commit breaks VLAN traffic flow between 2 switches
Hello guys, In a EX4300 stack SW-Cisco stack SW aggregated connection, I tried renaming an existing VLAN and using the previous VLAN to rename another existing VLAN in one commit as shown...
View ArticleRe: Disabling DHCP trapping
Hi, I am facing the exact same situation.. Have you figure out what was is the issue ?
View ArticleClik here to view.
ESXi VLAN tagging to Juniper switch not working
We have a situation where External Switch Tagging, which we prefer, will not work on some new HPE server while Virtual Switch Tagging works fine. This server is plugged into an EX4500 switch. The pdf...
View ArticleSSH Session to EX3300 VC hangs after connection established
Hello All, This is my first post so apologies if it's not as detailed or I miss something out. I was hoping you can help me with an odd problem I have. Scenario:I have a management subnet/vlan. An IP...
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Anyone? I'd appreciate any suggestions/pointers.
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Where are the layer 3 gateways for the two subnets? Any chance there is asymmetrical routing between these subnets.
View ArticleClik here to view.
unknown unicast on QFX5100 mc-lag irb
Hi All,I have strange problem with 2 * qfx5100 with mc-lag and irb + ospfMC-LAG peers have configured static-arp on irb interfaces. Everything works ok. Vlans without IRB works as it should be. But the...
View ArticleNeed a snapshot of EX2300 48-P
After I tried to zeroize the EX2300, It came back and lost all of its functionality.Meaning; Bricked and No Junos at all. I tried the top 10-google search/output, and no success.What I have tried?-...
View ArticleRe: unknown unicast on QFX5100 mc-lag irb
Hello,Do You have this line in the QFX config?set vlans <name>...
View ArticleRe: Need a snapshot of EX2300 48-P
If you were running 15.1X53-D56 or 15.1X53-D57 there is a known issue when you cannot recover the switch after doing a zeroize. I don't know if I can paste the solution here as it's not a public PR so...
View ArticleRe: Need a snapshot of EX2300 48-P
Hi Jonas, Thanks for your respond and Luckyly i was able to fix the whole system and have Full-functionallity! I did format a USB stick with the USB-image as download from the...
View Article