Re: Copy files using HTTPS on EX-Series devices
Hi, Did you find the fix for this? I have the same issue. ThanksChris
View ArticleEX9200 inter vlan routing inside a virtual switch
When I add a irb interface into a virtual-switch the L2 traffic seems to stop. Yet the irb interface is pingable. Is this even possible? How do I do L2 and L3 inside a virtual-switch? Thanks for any help
View ArticleEX9200 newly configured interface will not forward traffic intermittently
Sometimes with out reason when configuring a port for the first time on a EX9200 the port will not forward traffic yet it will link up. Yet if I reload both supervisors the link will start to work as...
View ArticleCisco to Juniper STP Configuration
The consulting company I work for does a fair number of projects where we remove older Cisco switches and replace them with Juniper switches. I'm labbing with physical switches and am running into...
View ArticleRe: Cisco to Juniper STP Configuration
Here's the output on the Cisco side: 3750-01#show spanning-tree vlan 110VLAN0110 Spanning tree enabled protocol rstp Root ID Priority 4206 Address 5006.0436.8400 This bridge is the root Hello Time 2...
View ArticleRe: Cisco to Juniper STP Configuration
Update: Converting the 3750 to MST and putting all VLANs in region0 is also a workable solution.
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Hello Spluka, Thanks for the response, the gateway for both subnets is the SRX firewall.
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
What happens when you connect via SSH from one switch to another (I.E. on the same layer two subnet)? If that works, then move a PC to the 10.1.1.0/24 subnet and try again. If the problem goes away,...
View ArticleEVENTD high cpu utilization 2300ex vc
Hello all.We are seeing this ONLY on 2300s *we have 3400 and 4300 actually doing more and not showing any stress*Ive disabled syslog and snmp on the switch . Im looking for a good doc that explains...
View Articlefpc0 LUCHIP(5): Secondary PPE 0 zone 2 timeout
Hi we have a Juniper EX9208 with Junos version below:Model: ex9208Junos: 16.1R5.7 We have noticed that the message log is filled with the following lines:May 2 08:08:27 COSMOS fpc0 LUCHIP(1):...
View ArticleRe: fpc0 LUCHIP(5): Secondary PPE 0 zone 2 timeout
Hi, Please find the below kb link for the similar messages.https://kb.juniper.net/InfoCenter/index?page=content&id=KB31713&act=login I hope this helps. Regards,Ajo Thomas
View ArticleRe: fpc0 LUCHIP(5): Secondary PPE 0 zone 2 timeout
Thanks, well it seems we will at least need to try restarting this line card or else maybe replacing it asap ...darn ... Something else that has been happening is that LACP bonds on that card have been...
View ArticleRe: EVENTD high cpu utilization 2300ex vc
So i found another post about turning up task accounting to see if that will help me.. I get nothing from this output showing the issuetask has been running for about 3 hours. Can anyone help point...
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
It does feel like a routing issue. Do either of the machines involved have multiple NIC? Is the default gateway or default route also pointed to the SRX gateway ip address on both sides?
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Thank you all for the help. SSH from switch to switch works fine. The route on the switch is set to the management network and points to the SRX as 10.1.1.1. There is only one NIC on the machines.
View ArticleRe: EX4200 running 15.1R5.5 unable to install J-web due to low free space
I downloaded the jweb-15.1R4.6-signed.tgz and attempted to install it, but I still have the issue of low free space. I also tried cleaning up the storage, but it didn't free up enough space. Any...
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Is this what your topology looks like? What you describe does sound like a routing issue, but your topology (at least what's been described thus far) is pretty simple, and the liklihood of a routing...
View ArticleRe: fpc0 LUCHIP(5): Secondary PPE 0 zone 2 timeout
Just to elaborate more on this in case someone has the same issue in the future with an EX9200 The card that is timing out has some crazy behaviour with LACP links, normal access ports or trunk ports...
View ArticleRe: SSH Session to EX3300 VC hangs after connection established
Is there an RVI on the switch in the laptop subnet that might be overriding the default route? what is the output ofshow route
View ArticleRe: EX4200 running 15.1R5.5 unable to install J-web due to low free space
From you description I assume you have runrequests system storage cleanup Also look at the home directories that may have files and /var/tmp for old software install files If you can't get enough space...
View Article