Re: Number of routed ports on EX3300-24T
I'm not sure what you mean by routed ports. But those are the main front panel port counts either 24 or 48 on the unit. In addition there are 4 uplink ports on the right side. Since you are using...
View ArticleEX2000 virtual chassis missing master
Hello, I'm hoping someone will help with suggestions with the following scenario: I have two EX2200 switches. After a power outage over the weekend the master does not boot: U-Boot 1.1.6 (Jul 26 2011 -...
View ArticleRe: EX2000 virtual chassis missing master
I might suggest you try to perform a USB upgrade/install on the switch. Follow USB instructions found here: https://kb.juniper.net/InfoCenter/index?page=content&id=KB20552 Good luck.
View ArticleRe: Two EX4300's, two different default forwarding class sets
And the answer is mixed-mode VC vs non. In a mixed-mode VC the default forwarding class set is the five classes as seen in switch2 above, with a regular VC having eight. This is odd behavior given that...
View ArticleRe: EX4200 Power Supply
The topic seems to fit my question quite well, so I write here.Do I understand correctly that I can also use smaller power supplies in an EX4200-48P, such as 320 WAC or 600 WAC?
View ArticleRe: EX4200 Power Supply
Hi good2know, The total power requirement for the device depends on the number of ports on which POE is enabled. If POE is not enabled on any port then smaller power supplies also will power the...
View ArticleRe: EX2000 virtual chassis missing master
Tried re-installing OS but got this: loader> install file:///jinstall-ex-2200-12.3R12.4-domestic-signed.tgz Package /jinstall-ex-2200-12.3R12.4-domestic-signed.tgz is signed... /kernel...
View ArticleRe: EX2000 virtual chassis missing master
Sorry, I can no longer assist. I assume you do not have a service contract, but if you do contact Juniper TAC for assistance.
View ArticleRe: EX2000 virtual chassis missing master
The other method you can try is from the working switch do a request system snapshot media usb and use this as a bootable image on the none working switch.Copy the install file to the usb and boot the...
View Articleincorrect snmp vcp statistics on ex4550
Hello, We've upgraded our juniper ex4550's in virtual chassis to version 15.1R6-S2.1. Everythig seems to be fine but one thing.Our aim was to have a simple way to get vc-port statistics over snmp. The...
View ArticlevQFX- PFE Wind River Linux 6.0.21 localhost console password
HelloHas anyone had this issue. when I install vQFX-PFE on EVE-NG, the local console password doesnt allow me to login.I used "root" "root"
View ArticleRe: vQFX- PFE Wind River Linux 6.0.21 localhost console password
The RE vm will drop us to the Junos prompt, like we’re used to. The only way to really tell that the PFE is fully loaded, is to login with “root/Juniper”, or try root wothout a password which is the...
View ArticleRe: EX3300 LLDP-MED and ShoreTel 400 series phone - works intermittently
Figured I would follow up on this. I had upgraded JunOS and still got the same issue. I pretty much walked away from this whole thing believing that there's just a problem with the hardware on these...
View ArticleRe: EX3400 - Recovery from failed SW upgrade fails
Hi, I've been trying this solution on an EX2300 and I haven't been able to get it too work. Here is the following output: can't load 'kernel' Type '?' for a list of commands, 'help' for more detailed...
View ArticleRe: EX3400 - Recovery from failed SW upgrade fails
I would suggest re-doing the USB drive, if that doesn't work try another USB drive (I've found in the past some work, some don't). Then power off the switch, plug in the drive, then boot.
View ArticleRe: EX3400 - Recovery from failed SW upgrade fails
Hi Eli, There are problems loading D55 by the method that I stated above. There are few tweaks required to install D55 which is not straight forward. It is better to install 15.1X53-D58 (JTAC...
View ArticleMC-LAG
Could you confirm me? Can I enable MC-LAG on rwo EX switches and manage devices as one logical device?I understand that It does.
View ArticleRe: MC-LAG
Sort of no and yes, with no being the more exact answer. Unlike VC, where there is one control plane, then the group of switches can be managed as 1. In MC-LAG there are two distinct control planes,...
View ArticleRe: vQFX- PFE Wind River Linux 6.0.21 localhost console password
Hi. The console credentials for vQFX PFE VM are "root/no". Agree with Alexander. The only way how to check that vQFX PFE VM is fully loaded is from CLI of vQFX RE VM (e.g. show chassis fpc). Default...
View ArticleRe: AFO/AFI airflow change on same Switche
Hi good2know. The Juniper SE or your reseller SE is your best contact for the part numbers.I have done some investigation and the SKUs for EX4550-32F are:EX4300-UM-BLNK EX4300 blank faceplate for...
View Article