Re: Converting media types between sa EX2200 and Cisco
Thanks for the reply. On the EX2200 and SRX they are both using the default vlan1. Since the Cisco switch belongs to another company I believe he's got the the port in trunk mode and allowing all...
View ArticleRe: Converting media types between sa EX2200 and Cisco
I highly suggest you use: set interface interface-namenative-vlan-id 1 on both the EX2200 and SRX if you want VLAN 1 to work with a Cisco, assuming the Cisco is using standard config, which it appears...
View ArticleRe: Converting media types between sa EX2200 and Cisco
So let me show what I got on both interface. EX interfacege-0/1/1unit 0 family ethernet-switchingport mode trunkvlan memebers allnative-vlan-id default SRX Interfacege-1/0/0unit 0 familty ethernet...
View ArticleRe: Converting media types between sa EX2200 and Cisco
Once again, change EX220 config for native-lan-id from default to 1, and on SRX from 14 to 1. That is best I can give you.
View ArticleRe: Converting media types between sa EX2200 and Cisco
Thx I'll give that a shot and wee what happens.
View ArticleRe: Q-in-Q to virtual router instance?
I am pretty sure it is possible with higher end switches such as EX4600.
View ArticleRe: interface-range config inheritance change
Thanks for the input dfex, but I'm not sure I completely follow your proposed solution. It sounds very cumbersome, which is what I am trying to avoid. Could you provide a few code snippets to...
View ArticleEX9200 SF2 Module interface
Hi, I have a question for ex9200 sf2 module.On the sf2 module, I could see two sfp interface beside External clock interface.I know that it can't be used as an Ethernet port, but I'm not sure where...
View ArticleRe: snapshoot proccess with EX4200
I know this is a few years too late, but the solution to your issue is: request system snapshot slice alernateHopefully this helps someone in the future.
View ArticleRe: ip helper in forwarding options
I dig up this thread just to thank you, that tip saved me from a lot of problem. I wasn't aware of source-address-giaddr And I had to configure a special NAT rule on the router between my ex3300 and...
View ArticleRe: interface-range config inheritance change
No problem - this is from a 4200-VC I have handy, but the principle is the same. I've created an interface-range with an access VLAN specified (remember this is slightly different to 4300 config):...
View ArticleRe: interface-range config inheritance change
Thanks for laying it, that's pretty much what I had thought you were getting at. Unfortunately it looks fairly cumbersome and I was looking to avoid having to modify the interface-ranges. Configuring...
View ArticleRe: What is different between helper bootp and dhcp-relay?
Yes, this is how I see the features working. Simple dhcp helper using bootp...
View ArticleRe: qsfp+ SR4 distances when splitted into 4x10GBaseSR ifs
After searching online for 40G QSFP+ SR4/ESR4 optics, I agree with you that ESR4 optics are much more expensive than SR4. Maybe you can choose JNP-QSFP-40G-LX4,(150m over OM4 MMF, 2km over SMF). This...
View ArticleVirtual Chassis LACP flap (GRES / NSB ?)
Hello,I have a topology composed of 6 EX3300 in VC.1 is master , one other is backup (botj have same weight, 129). The four others are linecard. I've done an upgrade from 12.3R9 to 12.3R12 few days...
View ArticleRe: Virtual Chassis LACP flap (GRES / NSB ?)
Hi, I doubt 'subscriber management' is related to the LACP link flaps.I would rather look at LACP and why LACP is timing out [LACPD_TIMEOUT messages].The following commands may provide more info:show...
View ArticleRe: Virtual Chassis LACP flap (GRES / NSB ?)
Hello, I use ae31 for example:root@sw-cloud-ex3300-stack> show lacp interfaces ae31 Aggregated interface: ae31 LACP state: Role Exp Def Dist Col Syn Aggr Timeout Activity ge-2/0/10 Actor No No Yes...
View ArticleRe: Virtual Chassis LACP flap (GRES / NSB ?)
Hi, NSB comes into play during Routing Engine failovers to maintain L2 Control Protocol information on the backup...
View ArticleRe: Virtual Chassis LACP flap (GRES / NSB ?)
Hi, thanks for fast answer. All my LACP interfaces flaped at same time:I did'nt find a RE failover.I've just done these commands to see switchover state: root@sw-cloud-ex3300-stack> show system...
View Article