Re: Configuring Member Ports in VC
Hello, Below is the requested output. FYI, I removed the other and only have just two members at the moment. root@1128_EX4300_VC# run show virtual-chassis statusVirtual Chassis ID:...
View ArticleRe: Configuring Member Ports in VC
I guess maybe it takes a while? I was changing some STP changes and I see them now. *Shrug* Thanks for your help though!
View ArticleRe: EX4200 Firewall Filter on A VLAN
Hi, The Firewall Filter proposed by Spuluka seems to be OK. you have to apply this Filter to your loopback lo0 unit 0.I hope it helps. BR/Zakour
View ArticleRe: EX4200 Firewall Filter on A VLAN
Hi, Applying firewall filter on the lo0.0 interface would not help in this case as this is transit traffic.Filters on lo0 are normally to protect the RE / control plane, i.e traffic destined to this...
View ArticleEX4500 12.3R10 doesn't support GRE?
I have a EX4500 need to configure a GRE tunnel. But I found there's no gr portsThe systerm version is:EX4500-1> show versionfpc0:...
View ArticleRe: EX4500 12.3R10 doesn't support GRE?
Hi, EX4500 does not support GRE in 12.3. You will need to upgrade to a newer version of JunOS. According to pathfinder GRE was added from 13.2X50D15. See pathfinder Tim
View ArticleEX2200 Virtual Chassis Cabling
When making a VC out of 3 EX2200 switches, is the cabling similar to how you can cable a 3300? For example, if I make 2 VC ports on each switch can I cable them in a daisy chain ring? I haven't been...
View ArticleRe: EX2200 Virtual Chassis Cabling
Hi, Yes the cabling is the same as you would use for EX3300. As long as you have a ring you will not have a split vc during a single failure event. Tim
View ArticleRe: EX2200 Virtual Chassis Cabling
Yes. This is correct in terms of cabling to build virtual chassis..
View ArticleRe: EX4500 12.3R10 doesn't support GRE?
For GRE tunnel to work and configure , you need to upgrade the JUNOS image latest to release R13
View ArticleRe: Configuring Member Ports in VC
Please try to restart the entire virtual chassi and then check the things !!!
View ArticlePort throughput
Hello Is there any way to check the throughput of each port in EX series switch so that we can determine the actual data flow ? Thanks in advance !!!
View ArticleRe: Port throughput
Hi, Maybe you could run "show interfaces | match rate". However, this does not indicate which interface.Alternatively, you could do snmp polling with some scripting. Cheers,Ashvin
View Article"Missing" VC ports in EX 4550 virtual chassis
Hi all,About 6 months ago, we added a 5th member to our then 4-member EX4550 VC. This new switch has an 8-port 10G module installed in it: FPC 4 REV 08 750-039070 LY0********* EX4550-32T CPU BUILTIN...
View ArticleRe: "Missing" VC ports in EX 4550 virtual chassis
Thanks, but I'm not sure how this helps me.
View ArticleRe: QFX5100-What is the RPM(revolutions per minutes) threshold in Fan Tray?
I'm not sure how to see the actual RPM stats for the general categories of normal, medium and high. The actual RPM do differ on the various platforms I've seen so they are somehow set per platform. I...
View ArticleRe: Steps to configure DHCP relay configuration using Server Groups in EX...
I'm not sure what you question or issue is here. What are you trying to configure?
View ArticleClik here to view.
Voice VLAN
Hi to all, One of the challenges I faced today at work , is a customer requesting to block data traffic on EX port configured as access data / voice vlan : set interfaces ge-0/0/2 unit 0 family...
View ArticleClik here to view.
Re: QFX5100-What is the RPM(revolutions per minutes) threshold in Fan Tray?
Hi Steve Yes, the fans in the FPC2 are spinning much faster and they sound much harder
View Article