Re: Firewall filter should not drop...but drop !
Sorry for being dense here, but if you are saying that both these addresses are outside the EX and NOT configured on any interface, then you are correct the filter should not drop the traffic....
View ArticleRe: Firewall filter should not drop...but drop !
The traffic is not destined for any IP associated with the RE, BUT the MAC is one associated with the EX4300 as these are routed packets. So IP no, MAC yes. I think you need TAC involvement and them to...
View ArticleRe: Firewall filter should not drop...but drop !
Thanks for your help dude, Model: ex4300-32fJunos: 14.1X53-D40.8 Yep, I look to the PR and open a case if needed. Thanks, --Salah
View ArticleMap 2 QinQ interfaces together with different outer VLAN IDs
Hi, On interface A QinQ is configured like this:vlan-tags outer 0x8100.1 inner 0x8100.600On interface B QinQ is configured like this:vlan-tags outer 0x8100.336 inner 0x8100.600these interfaces are in a...
View ArticleEX2200 - Junos 15.1R5 - broken Temperature Sensors
Hi, it seems there is something broken in Junos 15.1R5 with one of the temp sensors: root@switch> show chassis environment Class Item Status Measurement Power FPC 0 Power Supply 0 OK Temp FPC 0...
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Can we assume the sensor showed fine, before upgrade to 15.1R5? Which version of code were you previously on? Why might this not just be a defective sensor? Thanks
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Yes, prior to 15.1R5 it worked fine. I was on version 15.1R4 I observed the issue on two EX2200 and wouldn't expect an identical hardware failure at the same time. Just rolled back to 15.1R4 and temp...
View ArticleRe: Firewall filter should not drop...but drop !
in the meantime ">show firewall log detail" and see if it reveals more useful information
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
the weired thing is, if I run 15.1R5 and load the factory-default configuration, the alarm goes aways after after rebooting the switch. It's only shown a few seconds after reboot and it's...
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Just FYI, that I am trying to look into this. Do you have a case open with TAC? This would be need for any future Juniper action. When you have one, send me the number.
View ArticleRe: Map 2 QinQ interfaces together with different outer VLAN IDs
Hello,If You are doing this on MX series router, then You don't have to do anything, VLAN normalization takes care of translating the VLAN tags by default. More information here...
View ArticleClik here to view.
Re: Help needed!!! L2circuit @ ex2200
Here is my design challenge, basically I need to push all user traffic from LA site to SF site. SF site will provide all the resources and Internet access for LA site. Please see diag:Option 1To...
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Hello Chris, We would like to look into this more in JTAC . You could reach me at tkannan@juniper.net / +1 - 978-589-5809 regarding this issue and we would investigate further.
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
just tried to open a JTAC case, but I regognized the EX2200 boxes I'm using have no software maintenance. They are part of our lab equipement.As you already offered me to send you an email with details...
View ArticleDOT1x stopped working after Junos upgrade ex2200
This happened after we put new code on, from version 12.3R12.4 to 14.1X53-D40.8 cannot figure this out i can ping the NAC device from the switch, I looked in the nac and everything accpets until the...
View ArticleRe: DOT1x stopped working after Junos upgrade ex2200
down graded to 14.1X53-D35.3 same issue
View ArticleRe: DOT1x stopped working after Junos upgrade ex2200
i see 2 way traffic in my router show security flow session source-prefix 10.8.33.5 destination-prefix 10.0.0.14 Session ID: 44924, Policy name: LAN-Out/6, Timeout: 50, Valid In: 10.8.33.5/61018...
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Thank you! please let me know once you have sent the updated information.
View ArticleRe: ex3400 ip-source-guard?
Fyi I was told by our Juniper team that this feature could be expected with release 17.1 or 17.2 (already planned, but they are trying to move it up). Honestly, though with the small cost delta, we...
View Articleex3400 show route output
when I run show route I always get output where the route has a time of 00:00:00 listed. Is there a reason for this? The adjacency is stable: x.x.x.x/x *[OSPF/10] 00:00:00, metric 300> to x.x.x.x...
View Article