Re: Cannot get native vlan to pass data traffic on ELS EX4300
Hi WIll Could you please paste me the configuration under ge-0/0/10 interface ? Go to configure more and give show interface ge-0/0/10Need to check if native-vlan-id 51 is allowed as vlan member also...
View ArticleRe: ex3400 show route output
Sorry, I did not know this. I'm new to Juniper in general.
View ArticleRe: RSTP : Edge port with received BPDU > 0 ?
Hi Pascal Ideally in edge port you should never see BPDUs, you need to configure port security to block it or check the connected device why its sending BPDU In Non Edge port, Root switch will continue...
View ArticleRe: Ex2200 lacp flap
Hi Harvey What was the CPU utilisation Percentage at the time of this issue happened ?Is this device configured to send SNMP traps, if so you can check the SNMP monitoring tool for CPU percentage with...
View ArticleWhat the default action for storm-control default on QFX5100?
Hi All, May i know the default action will do by QFX5100 if storm happen at access switch that connected to QFX5100 as per below config. Is it the QFX will shut down the interface automatically even...
View ArticleRe: What the default action for storm-control default on QFX5100?
I believe the default action is log only. Maybe you could use the feedback button at the top of this URL to request the documentation for this be improved...
View ArticleScript in EX 2200
Hello, I want to know how I can do a script for all ours Switches in our network, I need to know which Switch has enabled:show configuration ethernet-switching-options secure-access-port interface all...
View ArticleRe: What the default action for storm-control default on QFX5100?
Hi rccpgm, It's look like the url that u given is more refering to EX series not for QFX. Thanks
View ArticleRe: What the default action for storm-control default on QFX5100?
QFX should be the same as new EX - EX with ELS, like EX4300 or EX4600.
View ArticleRe: What the default action for storm-control default on QFX5100?
EX and QFX both are the same, the default would be log.
View ArticleRe: Script in EX 2200
Hi tuff, can you please clarify your question, do you want to know which switch has a script enabled on it ??. or do you need a script. Thanks,Ramesh.G
View ArticleRe: Ex2200 lacp flap
Dec 11 19:17:40 XXXX chassism[1214]: JTASK_SCHED_SLIP_KEVENT: 21 sec 494516 usec kevent blockDec 11 19:17:40 XXXX sfid[1215]: JTASK_SCHED_SLIP_KEVENT: 21 sec 495211 usec kevent blockDec 11 19:17:40...
View ArticleL2 communication (VLAN)
Hello!It's my first post, so I'm going to say Hello to everybody! Also I'm sorry in advanced if this is not the right place (Ethernet switching) to post this message. First of all, this is my hardware...
View ArticleRe: L2 communication (VLAN)
Hi Jedrzej I hope the below pasted config belongs to the interface you are trying to make as Trunk portge-1/0/0 { unit 0 { family inet { address 192.168.253.34/30;...
View ArticleRe: L2 communication (VLAN)
Hi Arulav. Yes, this is the port I'm trying to make a trunk port. First one:admin@SM05_SRX> show ethernet-switching global-information ^syntax error, expecting <command>. Second:...
View ArticleRe: L2 communication (VLAN)
It looks like you want to have two routed links on the connection from the SRX to the EX switch with /30 addressing. This is not a layer 2 trunk port but layer 2 routed interfaces. Once the interface...
View ArticleRe: L2 communication (VLAN)
Hi Spuluka! Ok. So id did something like that:admin@SM05_SRX> show configuration interfaces ge-1/0/0vlan-tagging;unit 601 { vlan-id 601; family inet { address 192.168.253.34/30; } family iso;}unit...
View ArticleRe: L2 communication (VLAN)
An interesting use case. I don't know if that would work or not. The typical expectation is that the interface is either L2 or L3. But if you had the similar connection on the SRX to the second EX...
View ArticleRe: L2 communication (VLAN)
Hello,See if this helpshttps://forums.juniper.net/t5/SRX-Services-Gateway/Layer-2-and-Layer-3-logical-interfaces-on-same-physical/m-p/245170#M30096HTHThxAlex
View Article