Re: LAG loadbalancing method
ok. Juniper does load share, is this share equality bettween links in the same ae?. I have read, the share method is for IPv4 source, i think is very dificult the flows are share equiality every link,...
View ArticleRe: LAG loadbalancing method
Load sharing is NOT load balancing and since Juniper (and most others no matter what they might say) load shares, answer to load balancing is no. Now if you run say 1 million sessions through a LAG,...
View ArticleRe: Ex4300 Virtual Chassis member issue
rccpgm, Okay I will try Active/Passive routers in this case, and I'll troubleshoot from that point. By the way, I did not design the Juniper setup, I only continued the configuration to make it work....
View ArticleRe: Ex4300 Virtual Chassis member issue
i think you'll have MUCH better results, as this design is at like 100s of sites world wide. Wait to hear back with your results. Good luck.
View ArticleRe: Ex4300 Virtual Chassis member issue
Hey it worked! The first problem was solved. The devices can now ping each other vice versa whichever is the master switch. Now I know the issue is with the reth and AE interfaces. I have also...
View ArticleRe: Ex4300 Virtual Chassis member issue
Not sure of your exact set-up now, but if still having issues, suggest you send a diagram. You do realize that based upon your original diagram SRX A (one on left with ISP connection) is a single...
View ArticleRe: Blocking/Filtering BPDUs
By simpler words, I want to filter BPDUs, I don't want to block the port if BPDUs come in. Like Cisco's BPDU filter. This page describes what I want to do in Juniper:...
View ArticleRe: Ex4300 Virtual Chassis member issue
Actually I got it working now! I've reconfigured the reth interfaces and now the failover issue was gone. I can unplug any of the switch now without downtime. I can say that the issue is resolved now....
View ArticleRe: Blocking/Filtering BPDUs
Try instead set protocols layer2-control bpdu-block interface ge-0/0/0.0 dropCheers,Carsten
View ArticleRe: Set a trunk port with access VLAN issue
Hello Just to let you know that after deleting the native VLAN from the trunk section and let it only in the native section the problem disappear with linux serverNow the switch port respond to both...
View ArticleJuniper MX80 - Switching Traffic Between VLANs
Hi all, First thing first, apologize for any accidentally mistake like English explaintion, incorrect community category post...etc. The attached file is the diagram of the connectivity. We have one...
View Articleex3300 STP topology changes do not displayed.
Hi, everyone,I have strange problem on juniper ex3300. It's located in ring of switches (also junipers) that are in spanning tree domain( MSTP).Few weeks ago was noticed that when topology of mstp...
View ArticleEX4200 Cannot add L3 mac address in another vlan mac table
Hi, I have one L3 vlan (say 199) and one L2 vlan (say 200) on the same switch. They are connected together with a transparent proxy acting like a hub. An ethernet cable would do the trick too.On the L2...
View ArticleRe: [Q] How to get OOB on console port
Terminal server will allow for Async connect to console port and then also have an Ethernet connection to connect to an OOB switch network. For true OOB you should not use the switches interfaces on...
View ArticleRe: DHCP Snooping on EX4300 / ELS
I'm also interested to understand why this no longer appears to be supported. On a related note, be warned that we have been seeing very broken clients with dhcp-security, arp-inspection and...
View ArticleLink Fail over in EX
Hi, I need soluiton for route fail over in EX 4550, 2 MPLS links (primary & backup) terminated in switch & 1 up link to firewall. If primary fails, then traffic routed to backup link. In case...
View ArticleRe: LAG loadbalancing method
Junos works as per flow load blancing, and different platform might use different method to approach this.Eg, you can check below for legacy...
View ArticleEx3300 - How many Virtual Routers
I can find documentation on other models, but I can't seem to locate any definitive documentation that says how many virtual routers are supported on an EX3300 when combined with an EFL license?
View Article