Re: [Q] How to get OOB on console port
OK, you know I have several floors with atleast 4 switches on each floor. If the term serv is in the server room, and the link is down to a switch on one of the floors, is this going to work.?
View ArticleRe: [Q] How to get OOB on console port
This what a terminal server component is. In general some number of RS-232/Serial ports (today 9 pin connector) and at least one Ethernet LAN interface:...
View ArticleEX3300 RVI on Routing-instances (local routes rejected)
Hi, I tried to create routed vlan interface and placed it inside routing instance, based on my testing, from server i tried to ping my GW (Switch vlan interface) but its unreachable. I did this setup...
View ArticleRe: EX3300 RVI on Routing-instances (local routes rejected)
Routing-Instances do not create either a RVI - they create multiple different routing tables. I suggest you start over and read the EX Day-One book which covers how to create an RVI, as well as how to...
View ArticleRouting vlans to uplink
Hi all Sorry for this very basic question but I can't find a solutionI'm replacing old HP procurves with Juniper EX-4200 but I'm having troubles routing vlans to uplinkMy setup is very simple one vlan...
View ArticleRe: EX3300 RVI on Routing-instances (local routes rejected)
from Resolution Guide - EX - Troubleshoot VLAN interface KB22220 Is there at least one physical interface of that VLAN up and running ?No - In order to make a VLAN Interface active, at least one...
View ArticleRe: EX3300 RVI on Routing-instances (local routes rejected)
Got this, but what i mean here is i created routing instance to segregate 2 types of traffic and created rvi to forward packets between two vlans inside 1 routing instance.
View ArticleRe: Routing vlans to uplink
Are you sure there is a route back configured? If you can ping both networks from the switch it seems directly connected networks are ok, so L2/L3 are ok on the switch. The next step would be to look...
View ArticleRe: Link Fail over in EX
I can't think of a layer 2 solution, but did you consider solving this on layer3, with dynamic routing? OSPF, BGP can solve this.
View ArticleRe: Routing vlans to uplink
Thanks Screnie Because I have to be sure everything is working before to send the switch to the datacenter I was simulating the same network enviroment in my home lab, but you are right I didn't set a...
View ArticleRe: Link Fail over in EX
If you are using static routes, then qualified next-hop should work for you. http://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/policy-static-route-selection.html
View ArticleCreate RVI on ex4300
Trying to create an RVI on ex4300 but the below option isn't present...works on my ex2200-C. user@switch# set interfaces vlan unit logical-unit-number family inet address inet-address...
View ArticleRe: Create RVI on ex4300
Slightly different CLI on EX4300 and other newer models. Your issue is ELS CLI vs older EX CLI on EX2200. Look here for details and link to perform a translation of config from one to the other....
View ArticleRe: Create RVI on ex4300
Thanks, rccpgm! I figured it out and I will definitely use that link as a reference! I found this link that helped! I am more than likely running old code as you suggested....
View ArticleRe: Create RVI on ex4300
I have one last quick question if you have a second. I'm configuring the 4300 to be our Layer 3 core switch as we replace our cisco infrastructure. I was successful in linking l2 to l3 interface as...
View ArticleCan't Ping Internal IRB
Hello All, I'm new to Juniper and need some assistance. Current situation, we are in the process of migrating our cisco infrastructure to Juniper. Our ex4300 will serve as our core switches. After some...
View ArticleRe: Can't Ping Internal IRB
there was a similar question in this forum yesterday an IRB is only up when there is at least one active interface whith a corresponding vlan on the switch so check your irb state ( show interface irb...
View ArticleRe: Can't Ping Internal IRB
apologies, I'm not sure that I completely follow..but here is the output user@host# run show interfaces irbPhysical interface: irb, Enabled, Physical link is Up Interface index: 640, SNMP ifIndex: 501...
View ArticleRe: Create RVI on ex4300
Ping it how? From console connection? IP address should be ping able from any console connection, be it local or remote SSH/telnet. Sorry no idea what you are trying to do.
View ArticleRe: Can't Ping Internal IRB
Again with the routing-instance. You do NOT need a routing-instance to make this work. I would delete the routing instance and get it to work first, and THEN create and add to the routing instance....
View Article