Re: LACP EX3300 bandwidth issue
My suggest would to first break one-line in the AE and see what happens when traffic is routed, VLAN 1 ro VLAN 2. Then reconnect and break other side link and get that result. LAG/AE should have no...
View ArticleRe: LAG loadbalancing method
A LAG/AE does not load balance. Only way to actually load balance is to send one packet over LAG link #1, then next packet over LAG link #2, and so forth. This leads to potential for out of sequence...
View ArticleRe: MAC-Based Authentication EX4300 - AD Radius Server
I pulled only the key sections of the CLI being that there are 200 interfaces that would just clutter it up... also attached are some screenshots from the Radius config on Windows Server. ge-1/0/18 {...
View ArticleRe: LACP EX3300 bandwidth issue
Hi,Thanks we would check that .Your question if it is 10 GE .. no .. but I think I know why you ask that.. By saying 3.5Giga/min = 3500/60=58MBps
View ArticleRe: Ex4300 Virtual Chassis member issue
Hi rccpgm, Thank you for your input on this matter. When I removed the AE interfaces, the router was not able to reach the switch and the host connected to our SRX cannot ping the server connected on...
View ArticleRe: Ex4300 Virtual Chassis member issue
Something is wrong, obviously! The Reth works like active back-up. The secondary Node keeps the interface Up, but never sends and drops all receive. So you can not run an AE from the EX to the SRX...
View ArticleOver 10km connectivity query
A major project to migrate to new Datacentres within the next 12-14 months has started, as part of it there are 9 x 1Gb links which are currently under 10km to become greater than 10km in distance....
View ArticleRe: Over 10km connectivity query
John, #1 you should be having this discussion with your local Juniper partner and/or Juniper account team. As far as attenuation is concerned, as long as received signal is within specs no attenuation...
View ArticleRe: Ex4300 Virtual Chassis member issue
Hi rccpgm, Thank you very much for your help. I am trying to understand the situation based from what you all said in order to resolve this issue. So here is the chassis status of our SRX. The...
View ArticleRe: Over 10km connectivity query
Hi icthis, Regarding your first query related to the more than 10 KM 1G SFP requirement, its the first I've heard of this limitation and I've always known otherwise . I don't know what type of switch...
View ArticleRe: Over 10km connectivity query
With regards to the second part of your question related to the configuration of virtual chassis over long distances the setup you are looking for is referred to as "Extended Virtual Chassis...
View ArticleRe: Ex4300 Virtual Chassis member issue
You are running your SRX cluster as Active-Active? This is why nothing probably makes sense. If you run SRX A/A because the SRX is stateful FW you transmit and receive path MUST be the same or else...
View ArticleRe: EX4200/EX4500 does not pass via the GRE traffic going from devices...
I'm having the same issue as described at http://forums.juniper.net/t5/Routing/GRE-routing-issue/td-p/287911 (EX4550 running 14.1X53-D25.2) Has anyone succeeded to route traffic through GRE in...
View ArticleVME interface in subnet of an existing VLAN
Hi, I'm trying to configure an OOB management interface for a VC composed of 4 EX3300's. The vme interface's IP is 192.168.129.101 while there's a "management" VLAN on the switch which is...
View ArticleRe: VME interface in subnet of an existing VLAN
Hi marcodalli, Did you deactivate the me0 interface ? #deactivate interfaces me0
View ArticleRe: VME interface in subnet of an existing VLAN
I've deleted the me interface, don't know if that makes any difference....
View ArticleRe: VME interface in subnet of an existing VLAN
marcodalli wrote:Hi, I'm trying to configure an OOB management interface... Unfortunately you cannot, as you've discovered. This is a long-standing painful limitation with Juniper gear. I'd recommend...
View Article[Q] How to get OOB on console port
We have several floors with switches in the IDF's.I would like to know what your using to get to the console port on the different ports. Assume the switch uplink is down. thanks
View ArticleRe: [Q] How to get OOB on console port
If you want true OOB for console port, then I would suggest terminal servers not connected to local switch revenue port, but instead true OOB network [for the terminal servers].
View ArticleRe: VME interface in subnet of an existing VLAN
I do not believe his situation is related to Routing-Instances, as there was no mention of them to start with. In regards to routing-instances, yes me.0/vme.0 can only reside in default routing...
View Article