Re: Any one here have exprience integrate EX with Cobranet software?
Hi, the same as Steve. I haven't specifically worked with Cobranet, but have been providing ethernet-connectivity for various lighting and audio systems at the largest danish music festival and have...
View ArticleRe: Any one here have exprience integrate EX with Cobranet software?
Hi jonashauge / spuluka, From your feedback it's look like the Cobranet is totally cannot run under Layer 3. My Campus Design Building A connect to Buuilding B using OSPF (physical interface). Both of...
View ArticleRe: L2PT VCF QFX5100 - EX4300
Hi, Can you kindly tell if you have resovled that issue Regards
View ArticleRe: Any one here have exprience integrate EX with Cobranet software?
Your other option would be to build an l2circuit between the two buildings. We typically do these on the MX but the EX does support the feature too....
View ArticleEX2300 & Ex3300 VC Licenses over deployment scenario
Hi Can any one share knowledge over license required to activate Virtual chassis on EX 3300 ? i guess by default we can use 2 switches but for more i guess i need to buy license... but no sure which...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
Hi Hassan, VC licenses is only needed on EX2300. On all other EX platforms the VC functionality is provided without need for further licensing. Furthermore EX2200 and EX2300 can only do VC for up to 4...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
so its means 2300 is better to go with as 3300 will be costly and lower in specs... additionally, i also wanna know what will be the impact if i use 10G uplinks from each switch ? any more license per...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
EX3300 has better specs as it can do BGP and routing-instances with the right licenses. This is not found on the EX2300. Depending on port usage they are pretty close in price to each other when doing...
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
that was really helpful. just to update the deployment senario is of access layer... whereas team is not getting agree on 3300-48T as of the cost factor.... Thanks again. Regards,Hassan Mustafa
View ArticleRe: EX2300 & Ex3300 VC Licenses over deployment scenario
Actually these are questions either your Partner Account team or Juniper Account team should be able to answer easily. As for EX2300-VC (with extra license) vs EX3300-VC, if this is not yet purchased,...
View ArticleEX2200-48P - Avaya IP phones
Hi Is there any special poe requirements for this specific IP phones : Avaya E129 Because lately we're facing a problem that only this kind of IP phones is going down .It doesn't matter to which kind...
View ArticleEX4200 Virtual Chassis keeps going back and forth between Master and Backup
So I've configured two 4200 into a virtual chassis with a preprovisioned config. Whenever I remote into the management ip for the master I will remain logged into the master for about 5mins before the...
View ArticleRe: EX4200 Virtual Chassis keeps going back and forth between Master and Backup
Hi, Default behavior is you shouldnot get disconnected, can you please try a contuinuous ping and check the behavior.What is the status of the VC, do you always see both the members in the present...
View ArticleCoS on EX MDF and IDFs
Experts, I am including configuration from one of our switches and would like to get opinion the configuration is fine. version 12.3R12.4;groups { ezqos-voip { class-of-service { classifiers { dscp...
View ArticleRe: EX4200 Virtual Chassis keeps going back and forth between Master and Backup
If you are using short stacking cables you can possibly try using longer cables.I experienced a similar issue with EX3400s with a preprovisioned virtual chassis. Even though I believe these chassis may...
View ArticleClik here to view.
Adding VLANS QinQ to another VLAN (see notes!)
Not sure how I should title this (C in S Tagging, double tagging, QinQ)?! I have two switches which I have untagged ports with QinQ enabled on them, those switches take the taffic and each put them in...
View ArticleRe: Adding VLANS QinQ to another VLAN (see notes!)
What you want is standard Q-in-Q operation. You will not get Q-in-Q on an access port, only on a trunk/tagged port. What you do is send the C-VLAN information (100/200) in as tagged into an access...
View ArticleRe: Adding VLANS QinQ to another VLAN (see notes!)
Since the connection between the C-Switch to the P-Switch is trunk, you can have multiple C-VLAN tagged with single S-VLAN and passed across the P-Switch. ThanksArul
View ArticleRe: EX2200-48P - Avaya IP phones
Class 1 uses minimum 0.44W and maximum is 3.84W You can try by setting the maximum power for that particular port where Avaya switch is connected. root# set poe interface ge-0/0/0 maximum-power...
View ArticleRe: EX2200 - Junos 15.1R5 - broken Temperature Sensors
Hi Steve, thanks.I downgraded to 12.3 (last recommended) and it worked again. I will track the PR and get in touch with JTAC. RegardsChris
View Article