Re: Cant find device AE21
seem the only problem is it is down: ae21 up downae21.0 up down eth-switch Both ports are connected
View ArticleRe: Cant find device AE21
Physical interface: ae21, Enabled, Physical link is Down I have all configured like other ae and other ae is up and running .......
View ArticleRe: Cant find device AE21
looks like both ports have inactive ether option but when I do actiavte ether option I have 'unit 0' logical unit is not allowed on aggregated linkserror: configuration check-out failed
View ArticleHigh CPU Utilisation withDHCP/ LACP/DOT1x/NTP Not working
Ex3400 or Ex2300 ships with 15.1X53-D50.With this code LACP Dot1x ,DHCP and other timer related protcols wil not work.The Root cause seems to be system clock showing incorrect time 2038. Solution and...
View ArticleRe: ELS and QinQ and Layer 2 Protocol Tunneling
Please try to set the native vlan ID on the interface facing the CE. JTAC@EXSWITCH# show interfaces ge-0/0/1 description port-facing-CE;flexible-vlan-tagging;native-vlan-id 1;encapsulation...
View ArticleRe: Juniper switchport configuration
Thank You Gentelmen, In 4300 EX we use Junos: 14.1X53-D35.3. I work curently with Juniper Tech and we rulled out its not STP, either PoE. Looks like we might look specifically into each category...
View ArticleRe: ELS and QinQ and Layer 2 Protocol Tunneling
eeskiyen wrote:Please try to set the native vlan ID on the interface facing the CE. JTAC@EXSWITCH# show interfaces ge-0/0/1 description port-facing-CE;flexible-vlan-tagging;native-vlan-id...
View ArticleRe: EX-2200-c restart interfaces every few seconds
If this is happening with only one switch then its a hardware issue.what is the Junos version?
View ArticleRe: ex3400 show route output
15.1X53-D55 is released and this code addresses multiple poe related issues.
View ArticleRe: arp inspection fails on specific vlan
what is the ex model you are seeing tihs issue.what is the Junos version?Are there any logs indicating failure
View ArticleRe: 802.1x broken in Junos 15.1R5.5
we need to look at the captures .Could be a problem in junos 15.1.Can you enable traceoptions for better clarity.
View ArticleRe: ELS and QinQ and Layer 2 Protocol Tunneling
Hi, thanks for the assistance. I tried to set native vlan for CE interfaces and CDP traffic started passthrouth, but still PVST+ frames has only one VLAN tag on trunk interfaces, which is wrong. So...
View ArticleRe: EX-2200-c restart interfaces every few seconds
During the down period can you run these to see what alarms are active show chassis alarmsshow system alarms
View ArticleEX2300-24T uplink port
Dear ALL, We would like to purchase EX2300-24T as iSCSI SAN switch , our SAN model is HPE MSA 1040 10G iSCSI, Can we use the 4 x 10G uplink port connect to HPE MSA 1040 10G port(not mangement port)?...
View ArticleRe: ELS and QinQ and Layer 2 Protocol Tunneling
PVST+ are sent as untagged frames using native vlan-id 1. Is the native-vlan-id you configured vlan 1?
View ArticleRe: EX4300 PVLAN propagation
I am having the same issue on ex3400 units.I am configuring Private VLANS and am seeing the following: I have multiple Primary VLANs each with their own isolated VLAN. on my uplink port I have all the...
View ArticleRe: EX2300-24T uplink port
Yes, the 4x SFP+ interfaces can accept 10Gb trancievers and be configured as standard ethernet ports.
View ArticleRe: EX4300 PVLAN propagation
Remember the whole purpose of the PVLAN is to basically nest sub-vlans into a primary vlan. Your configuration does not show a primary vlanAssociate the isolated VLAN with the primary VLAN:[edit vlans...
View Article