vQFX10k 15.1X53-D60 on ESXi Installation and Running with up to 10 Interfaces
Hi ! Ther are some info on installing the vQFX10k , this one was helpful for me vQFX 10k Testlab on ESX 6.0 / 6. (NOTE that the RE needs a lot of memory if you add interfaces, I use 6GB/RE) but on...
View ArticleConnecting Cisco4900M with VC 4300 EX no luck
Experts, I am trying to connect using active / passive link aggregation Juniper VC 4300 with Cisco 4900M using SFP module on Cisco - Cisco CVR-X2-SFP10G= X2 TO SFP+ADAPTOR MODULE with Juniper SFP+...
View ArticleRe: mac-move-limit action log on EX switches causes delay and packet loss
Hello, as the action is only log, it should not cause issues, at least to my understanding. Especially because the move limit apparently was never hit, as I did not receive logs about any mac move.I...
View ArticleRe: vQFX10k 15.1X53-D60 on ESXi Installation and Running with up to 10...
Installing and Running vQFX on Vmware Workstation Take the virtualbox-version and expand the file 2 times with a zip-program (eg. 7zip)The pfe can be started by opening the box.ovf in VMware ( ignore...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
The configuration is fallowing but I believe its fine: I have ether channel 2 configured on Cisco 4900: interface Port-channel2switchportswitchport trunk native vlan 5switchport mode trunkload-interval...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
have you enabled "service unsupported-transceiver" on your 4900M ? If not you will need this command to allow 3rd party optics. The command is hidden so you need to type it in full. Please revert with...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
no i did not, i will try and post results Thank You so much Jonas - and have a nice weekend !!! -Adam
View Articlevxlan l3 gateway
trying to set vmx as a l3 vxlan gw, however irb's are not coming up. any advise what is missing? vmx-1> show interfaces terse | match irb irb up upirb.1100 up down inet 10.1.11.252/24...
View ArticleRe: vxlan l3 gateway
HI !As far as I know the current public available versions of the vMX do NOT support EVPN/VXLAN. if you want to play with EVPN/VXLAN-L3 you need either a physical MX (junos version 14.2R7.5) or a...
View ArticleAirtame - SSDP Across VLANs
My company is deploying Airtame wireless HDMI/presentation devices. They are actually pretty nice. However, we want to get the discovery features working. This device uses SSDP for that, but we'll...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
tried that and also other commands: no errdisable detect cause gbic-invalid no luck - still both ports down Juniper uses...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
Hi Logtech, bollocks. Another question: distance of the SFP+ cable? I see that 7 meter cables are supported by EX3400 but the OneX only supports up to 5 meters. If the cable is only 5 meters, please...
View ArticleRe: vxlan l3 gateway
it looks answer was in other thread: #####################################vMX #######################Re: Commit error with encapsulation vxlan Options10-08-2016 12:30 AM Please NOTE that the the...
View ArticleRe: Airtame - SSDP Across VLANs
Hello,What is the Airtame SSDP TTL? If it is >1, see if this...
View ArticleRe: Connecting Cisco4900M with VC 4300 EX no luck
I dont think its cable since its 2 ft cable - same cable is used for connecting all 4300 in virtual chasis, I will play a bit of with configuration over this weekend, I assume its Cisco OneX module...
View Articleconnecting two routers to ine switch ex2200 4g
hello recently i did a project in 3 floors building 'i used 8 switch from juniper ex 22000 48 - 4g poe i used the default vlan ' and configure lag with lacp enableto all floors from master switch. i...
View ArticleRe: connecting two routers to ine switch ex2200 4g
Thanks for the topology. You will need to separate the traffic from the cameras and your VDSL device using 10.0.0.138 into a different VLAN from your global default VLAN for traffic in the...
View ArticleEX3300 VCs unexpectedly generates new ssh hostkeys after reboot
Hello,we have a strange problem with our EX3300 series switches virtual chassis (VCs), running Junos 12.3R3.4. Most of them running over years without an issue, but since the last month we where faced...
View Article